参数资料
| 型号： | LT6201IS8#TR |
| 厂商： | Linear Technology |
| 文件页数： | 14/26页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP DL 165MHZ R-R I/O 8SOIC |
| 标准包装： | 2,500 |
| 放大器类型： | 缓冲器 |
| 电路数： | 2 |
| 输出类型： | 满摆幅 |
| 转换速率： | 50 V/µs |
| 增益带宽积： | 165MHz |
| 电流 - 输入偏压： | 23µA |
| 电压 - 输入偏移： | 2500µV |
| 电流 - 电源： | 20mA |
| 电流 - 输出 / 通道： | 90mA |
| 电压 - 电源，单路/双路(±)： | 2.5 V ~ 12.6 V，±1.25 V ~ 6.3 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 带卷 (TR) |
21
62001ff
LT6200/LT6200-5
LT6200-10/LT6201
Figure 2 shows the input and output waveforms of the
LT6200 driven into clipping while connected in a gain of
AV = 1. In this photo, the input signal generator is clipping
at±35mA,andtheoutputtransistorssupplythisgenerator
current through the protection diodes.
applicaTions inForMaTion
15MHz/DIV
100kHz
150kHz
0V
VCC
2.5V
VEE
–2.5V
6200 F02
Figure 2. VS = ±2.5V, AV = 1 with Large Overdrive
ESD
The LT6200 has reverse-biased ESD protection diodes on
all inputs and outputs, as shown in Figure 1. If these pins
are forced beyond either supply, unlimited current will
flow through these diodes. If the current is transient and
limitedto30mAorless,nodamagetothedevicewilloccur.
Noise
The noise voltage of the LT6200 is equivalent to that of
a 56Ω resistor—and for the lowest possible noise, it is
desirable to keep the source and feedback resistance
at or below this value (i.e., RS + RG//RFB ≤ 56Ω). With
RS + RG//RFB = 56Ω the total noise of the amplifier is:
en = √(0.95nV)2 + (0.95nV)2 = 1.35nV. Below this resis-
tance value the amplifier dominates the noise, but in the
resistance region between 56Ω and approximately 6kΩ,
the noise is dominated by the resistor thermal noise. As
the total resistance is further increased, beyond 6k, the
noise current multiplied by the total resistance eventually
dominates the noise.
For a complete discussion of amplifier noise, see the
LT1028 data sheet.
Power Dissipation
The LT6200 combines high speed with large output cur-
rent in a small package, so there is a need to ensure that
the die’s junction temperature does not exceed 150°C.
The LT6200 is housed in a 6-lead TSOT-23 package. The
package has the V– supply pin fused to the lead frame to
enhance the thermal conductance when connecting to a
ground plane or a large metal trace. Metal trace and plated
through-holescanbeusedtospreadtheheatgeneratedby
the device to the backside of the PC board. For example,
on a 3/32" FR-4 board with 2oz copper, a total of 270mm2
connects to Pin 2 of the LT6200 (in a TSOT-23 package)
bringing the thermal resistance,
θJA, to about 135°C/W.
Without an extra metal trace beside the power line con-
necting to the V– pin to provide a heat sink, the thermal
resistance will be around 200°C/W. More information on
thermal resistance with various metal areas connecting
to the V– pin is provided in Table 1.
Table 1. LT6200 6-Lead TSOT-23 Package
COPPER AREA
TOPSIDE (mm2)
BOARD AREA
(mm2)
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
270
2500
135C/W
100
2500
145C/W
20
2500
160C/W
0
2500
200C/W
Device is mounted on topside.
Junction temperature TJ is calculated from the ambient
temperature TA and power dissipation PD as follows:
TJ = TA + (PD θJA)
The power dissipation in the IC is the function of the sup-
ply voltage, output voltage and the load resistance. For
a given supply voltage, the worst-case power dissipation
PD(MAX) occurs at the maximum quiescent supply current
and at the output voltage which is half of either supply
voltage (or the maximum swing if it is less than half the
supply voltage). PD(MAX) is given by:
PD(MAX) = (VS IS(MAX)) + (VS/2)2/RL
Example: An LT6200 in TSOT-23 mounted on a 2500mm2
area of PC board without any extra heat spreading plane
connected to its V– pin has a thermal resistance of
相关PDF资料 |
PDF描述 |
|---|---|
| 0001.2504 | FUSE 1A 250V 5X20 T-LAG CERM |
| 32981 | CONN SPAD 16-22 AWG #8 PLASTI-GP |
| 34155 | CONN SPADE 16-22 AWG #8 PL-GRP |
| 0001.1014 | FUSE 10A 250V 5X20 FAST-ACT CERM |
| 34167 | CONN SPADE 14-16 AWG #10 P-GRIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT6201IS8TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:165MHz, Rail-to-Rail Input and Output, 0.95nV/√Hz Low Noise, Op Amp Family |
| LT6202 | 制造商:LINER 制造商全称:Linear Technology 功能描述:18-Bit, 1.6Msps, Pseudo-Differential Unipolar SAR |
| LT6202CS5 | 制造商:Linear Technology 功能描述:OP Amp Single GP R-R I/O ±6.3V/12.6V 5-Pin TSOT-23 |
| LT6202CS5#PBF | 制造商:Linear Technology 功能描述:OP-AMP 100MHZ 25V/us TSOT-2 制造商:Linear Technology 功能描述:OP-AMP, 100MHZ, 25V/us, TSOT-23-5; Op Amp Type:Unity Gain Stable; No. of Amplifiers:1; Slew Rate:25V/s; Supply Voltage Range:2.5V to 12.6V; Amplifier Case Style:TSOT-23; No. of Pins:5; Bandwidth:100MHz; Operating Temperature Min:0C;RoHS Compliant: Yes |
| LT6202CS5#TR | 功能描述:IC OPAMP R-R 100MHZ SGL TSOT23-5 RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。