- 您现在的位置：买卖IC网 > PDF目录3519 > LT6203CMS8#TRPBF (Linear Technology)IC OPAMP R-R INOUT DUAL LP 8MSOP PDF资料下载
参数资料
| 型号： | LT6203CMS8#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP R-R INOUT DUAL LP 8MSOP |
| 标准包装： | 2,500 |
| 放大器类型： | 通用 |
| 电路数： | 2 |
| 输出类型： | 满摆幅 |
| 转换速率： | 25 V/µs |
| 增益带宽积： | 100MHz |
| 电流 - 输入偏压： | 3.8µA |
| 电压 - 输入偏移： | 2600µV |
| 电流 - 电源： | 2.8mA |
| 电流 - 输出 / 通道： | 40mA |
| 电压 - 电源，单路/双路(±)： | 2.5 V ~ 12.6 V，±1.25 V ~ 6.3 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT6202/LT6203/LT6204
19
620234fd
APPLICATIONS INFORMATION
Input Protection
There are back-to-back diodes, D1 and D2, across the
+ and – inputs of these amplifiers to limit the differential
input voltage to ±0.7V. The inputs of the LT6202/LT6203/
LT6304 do not have internal resistors in series with the
input transistors. This technique is often used to protect
the input devices from over voltage that causes excessive
currents to flow. The addition of these resistors would
significantly degrade the low noise voltage of these ampli-
fiers.Forinstance,a100Ωresistorinserieswitheachinput
would generate 1.8nV/√Hz of noise, and the total amplifier
noise voltage would rise from 1.9nV/√Hz to 2.6nV/√Hz.
Once the input differential voltage exceeds ±0.7V, steady
state current conducted though the protection diodes
should be limited to ±40mA. This implies 25Ω of protec-
tion resistance per volt of continuous overdrive beyond
±0.7V. The input diodes are rugged enough to handle
transient currents due to amplifier slew rate overdrive or
momentary clipping without these resistors.
Figure 2 shows the input and output waveforms of the
amplifier driven into clipping while connected in a gain
of AV = 1. When the input signal goes sufficiently beyond
the power supply rails, the input transistors will saturate.
When saturation occurs, the amplifier loses a stage of
phase inversion and the output tries to change states.
Diodes D1 and D2 forward bias and hold the output within
OV
Figure 2. VS = ±2.5V, AV = 1 with Large Overdrive
a diode drop of the input signal. In this photo, the input
signal generator is clipping at ±35mA, and the output
transistors supply this generator current through the
protection diodes.
With the amplifier connected in a gain of AV ≥ 2, the output
can invert with very heavy input overdrive. To avoid this
inversion, limit the input overdrive to 0.5V beyond the
power supply rails.
ESD
The LT6202/LT6203/LT6204 have reverse-biased ESD
protection diodes on all inputs and outputs as shown in
Figure 1. If these pins are forced beyond either supply,
unlimited current will flow through these diodes. If the
current is transient and limited to one hundred milliamps
or less, no damage to the device will occur.
Noise
The noise voltage of the LT6202/LT6203/LT6204 is equiva-
lent to that of a 225Ω resistor, and for the lowest possible
noise it is desirable to keep the source and feedback re-
sistance at or below this value, i.e. RS + RG||RFB ≤ 225Ω.
With RS + RG||RFB = 225Ω the total noise of the amplifier
is: en = √(1.9nV)2+(1.9nV)2 = 2.7nV. Below this resis-
tance value, the amplifier dominates the noise, but in the
resistanceregionbetween225Ωandapproximately10kΩ,
the noise is dominated by the resistor thermal noise. As
the total resistance is further increased, beyond 10k, the
noise current multiplied by the total resistance eventually
dominates the noise.
The product of en √ISUPPLY is an interesting way to gauge
lownoiseamplifiers.Manylownoiseamplifierswithlowen
have high ISUPPLY current. In applications that require low
noise with the lowest possible supply current, this product
can prove to be enlightening. The LT6202/LT6203/LT6204
have an en, √ISUPPLY product of 3.2 per amplifier, yet it is
commontoseeamplifierswithsimilarnoisespecifications
have an en √ISUPPLY product of 4.7 to 13.5.
For a complete discussion of amplifier noise, see the
LT1028 data sheet.
相关PDF资料 |
PDF描述 |
|---|---|
| MMS-112-01-L-SH | CONN RCPT 2MM 12POS SGL HORZ PCB |
| MMS-113-01-L-SH | CONN RCPT 2MM 13POS SGL HORZ PCB |
| MMS-118-01-L-SH | CONN RCPT 2MM 18POS SGL HORZ PCB |
| SSQ 8 | FUSE 8A 125V 6125 FAST SSQ |
| MMS-119-01-L-SH | CONN RCPT 2MM 19POS SGL HORZ PCB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT6203CS8 | 功能描述:IC OPAMP R-R INOUT DUAL LP 8SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:电流检测 电路数:1 输出类型:- 转换速率:- 增益带宽积:125kHz -3db带宽:- 电流 - 输入偏压:- 电压 - 输入偏移:100µV 电流 - 电源:1.1µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:4-WFBGA，CSPBGA 供应商设备封装:4-UCSP（2x2） 包装:剪切带 (CT) 其它名称:MAX9634WERS+TCT |
| LT6203CS8#PBF | 功能描述:IC OPAMP R-R INOUT DUAL LP 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:MicroAmplifier™ 放大器类型:通用 电路数:4 输出类型:- 转换速率:3.5 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:5pA 电压 - 输入偏移:1500µV 电流 - 电源:220µA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):4.5 V ~ 36 V，±2.25 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:剪切带 (CT) 其它名称:296-29363-1 |
| LT6203CS8#PBF | 制造商:Linear Technology 功能描述:Operational Amplifier (Op-Amp) IC |
| LT6203CS8#TR | 功能描述:IC OPAMP R-R INOUT DUAL LP 8SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:电流检测 电路数:1 输出类型:- 转换速率:- 增益带宽积:125kHz -3db带宽:- 电流 - 输入偏压:- 电压 - 输入偏移:100µV 电流 - 电源:1.1µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:4-WFBGA，CSPBGA 供应商设备封装:4-UCSP（2x2） 包装:剪切带 (CT) 其它名称:MAX9634WERS+TCT |
| LT6203CS8#TRPBF | 功能描述:IC OPAMP R-R INOUT DUAL LP 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:电流检测 电路数:1 输出类型:- 转换速率:- 增益带宽积:125kHz -3db带宽:- 电流 - 输入偏压:- 电压 - 输入偏移:100µV 电流 - 电源:1.1µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:4-WFBGA，CSPBGA 供应商设备封装:4-UCSP（2x2） 包装:剪切带 (CT) 其它名称:MAX9634WERS+TCT |
发布紧急采购，3分钟左右您将得到回复。