- 您现在的位置：买卖IC网 > PDF目录8545 > LT6206IMS8#TRPBF (Linear Technology)IC OPAMP VID DUAL 100MHZ 8-MSOP PDF资料下载
参数资料
| 型号： | LT6206IMS8#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 4/18页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP VID DUAL 100MHZ 8-MSOP |
| 标准包装： | 2,500 |
| 应用： | 电压反馈 |
| 输出类型： | 满摆幅 |
| 电路数： | 2 |
| 转换速率： | 600 V/µs |
| 电流 - 电源： | 4mA |
| 电流 - 输出 / 通道： | 60mA |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 12.6 V，±1.35 V ~ 6.3 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
LT6205/LT6206/LT6207
12
620567fc
APPLICATIONS INFORMATION
Amplier Characteristics
Figure 1 shows a simplied schematic of the LT6205/
LT6206/LT6207. The input stage consists of transistors
Q1 to Q8 and resistor R1. This topology allows for high
slew rates at low supply voltages. The input common
mode range extends from ground to typically 1.75V from
VCC, and is limited by 2 VBEs plus a saturation voltage of
a current source. There are back-to-back series diodes,
D1 to D4, across the + and – inputs of each amplier to
limit the differential voltage to ±1.4V. RIN limits the current
through these diodes if the input differential voltage exceeds
±1.4V. The input stage drives the degeneration resistors of
PNP and NPN current mirrors, Q9 to Q12, which convert
the differential signals into a single-ended output. The
complementary drive generator supplies current to the
output transistors that swing from rail-to-rail.
The current generated through R1, divided by the capacitor
CM, determines the slew rate. Note that this current, and
hence the slew rate, are proportional to the magnitude
of the input step. The input step equals the output step
divided by the closed loop gain. The highest slew rates
are therefore obtained in the lowest gain congurations.
The Typical Performance Characteristics curve of Slew
Rate vs Closed-Loop Gain shows the details.
ESD
The LT6205/LT6206/LT6207 have reverse-biased ESD
protection diodes on all inputs and outputs as shown in
Figure 1. If these pins are forced beyond either supply
unlimited current will ow through these diodes. If the
current is transient, and limited to 25mA or less, no dam-
age to the device will occur.
Layout and Passive Components
With a gain bandwidth product of 100MHz and a slew rate
of 450V/μs the LT6205/LT6206/LT6207 require special
attention to board layout and supply bypassing. Use a
ground plane, short lead lengths and RF quality low ESR
supply bypass capacitors. The positive supply pin should
be bypassed with a small capacitor (typically 0.01μF to
0.1μF) within 0.25 inches of the pin. When driving heavy
loads, an additional 4.7μF electrolytic capacitor should be
used. When using split supplies, the same is true for the
negative supply pin. For optimum performance all feedback
components and bypass capacitors should be contained
in a 0.5 inch by 0.5 inch area. This helps ensure minimal
stray capacitances.
The parallel combination of the feedback resistor and gain
setting resistor on the inverting input can combine with
the input capacitance to form a pole which can degrade
stability. In general, use feedback resistors of 1k or less.
Capacitive Load
The LT6205/LT6206/LT6207 are optimized for wide band-
width video applications. They can drive a capacitive load
of 20pF in a unity-gain conguration. When driving a
larger capacitive load, a resistor of 10Ω to 50Ω should
be connected between the output and the capacitive load
to avoid ringing or oscillation. The feedback should still
be taken from the output pin so that the resistor will
isolate the capacitive load and ensure stability. The Typi-
cal Performance Characteristics curves show the output
overshoot when driving a capacitive load with different
series resistors.
Video Signal Characteristics
Composite video is the most commonly used signal in
broadcast grade products and includes luma (or lumi-
nance, the intensity information), chroma (the colorimetry
information) and sync (vertical and horizontal raster tim-
ing) elements combined into a single signal, NTSC and
PAL being the common formats. Component video for
entertainment systems include separate signal(s) for the
luma and chroma (i.e., Y/C or YPbPr) with sync generally
applied to the luma channel (Y signal). In some instances,
native RGB signals (separate intensity information for each
primary color: red, green, blue) will have sync included as
well. All the signal types that include sync are electrically
similar from a voltage-swing standpoint, though various
timing and bandwidth relationships exist depending on
the applicable standard.
The typical video waveforms that include sync (includ-
ing full composite) are specied to have nominal 1VP-P
amplitude. The lower 0.3V is reserved for sync tips that
carry timing information, and by being at a lower potential
than all the other information, represents blacker-than-
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J0Z-MZ-B1 | CONVERTER MOD DC/DC 2V 10W |
| VE-J0Y-MZ-B1 | CONVERTER MOD DC/DC 3.3V 16.5W |
| 208283-4 | CONN RCPT CPC 4POS SZ11 REV |
| 208283-1 | CONN RCPT CPC 4POS SZ11 REV |
| HI5760IAZ | CONV D/A 10-BIT 125MSPS 28-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT6207 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Single/Dual/Quad Single Supply 3V, 100MHz Video Op Amps |
| LT6207CGN | 功能描述:IC OP AMP VIDEO QUAD 3V 16-SSOP RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| LT6207CGN#PBF | 功能描述:IC OP AMP VIDEO QUAD 3V 16-SSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
| LT6207CGN#TR | 功能描述:IC OPAMP VID QUAD 100MHZ 16-SSOP RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| LT6207CGN#TRPBF | 功能描述:IC OP AMP VIDEO QUAD 3V 16-SSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。