- 您现在的位置：买卖IC网 > PDF目录10075 > LT6300IGN#TRPBF (Linear Technology)IC XDSL LINE DRIVER 16-SSOP PDF资料下载
参数资料
| 型号： | LT6300IGN#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC XDSL LINE DRIVER 16-SSOP |
| 标准包装： | 2,500 |
| 类型： | 线路驱动器，发射器 |
| 驱动器/接收器数： | 2/0 |
| 规程： | xDSL |
| 电源电压： | 5 V ~ 12 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 带卷 (TR) |
11
LT6300
APPLICATIO S I FOR ATIO
WU
UU
Heat Sinking Using PCB Metal
Designing a thermal management system is often a trial
and error process as it is never certain how effective it is
until it is manufactured and evaluated. As a general rule,
the more copper area of a PCB used for spreading heat
away from the driver package, the more the operating
junction temperature of the driver will be reduced. The
limit to this approach however is the need for very com-
pact circuit layout to allow more ports to be implemented
on any given size PCB.
To best extract heat from the GN16 package, a generous
area of top layer PCB metal should be connected to the four
corner pins (Pins 1, 8, 9 and 16). These pins are fused to
the leadframe where the LT6300 die is attached. It is
important to note that this heat spreading metal area is
electrically connected to the V– supply voltage.
Fortunately xDSL circuit boards use multiple layers of
metal for interconnection of components. Areas of metal
beneath the LT6300 connected together through several
small 13 mil vias can be effective in conducting heat away
from the driver package. The use of inner layer metal can
free up top and bottom layer PCB area for external compo-
nent placement.
When PCB cards containing multiple ports are inserted
into a rack in an enclosed cabinet, it is often necessary to
provide airflow through the cabinet and over the cards.
This is also very effective in reducing the junction-to-
ambient thermal resistance of each line driver. To a limit,
this thermal resistance can be reduced approximately
5
°C/W for every 100lfpm of laminar airflow.
Layout and Passive Components
With a gain bandwidth product of 200MHz the LT6300
requires attention to detail in order to extract maximum
performance. Use a ground plane, short lead lengths and
a combination of RF-quality supply bypass capacitors (i.e.,
0.1
F). As the primary applications have high drive cur-
rent, use low ESR supply bypass capacitors (1
F to 10F).
The parallel combination of the feedback resistor and gain
setting resistor on the inverting input can combine with
the input capacitance to form a pole that can cause
frequency peaking. In general, use feedback resistors of
1k or less.
Compensation
The LT6300 is stable in a gain 10 or higher for any supply
and resistive load. It is easily compensated for lower gains
with a single resistor or a resistor plus a capacitor.
Figure 8 shows that for inverting gains, a resistor from the
inverting node to AC ground guarantees stability if the
parallel combination of RC and RG is less than or equal to
RF/9. For lowest distortion and DC output offset, a series
capacitor, CC, can be used to reduce the noise gain at
lower frequencies. The break frequency produced by RC
and CC should be less than 5MHz to minimize peaking.
Figure 9 shows compensation in the noninverting configu-
ration. The RC, CC network acts similarly to the inverting
case. The input impedance is not reduced because the
network is bootstrapped. This network can also be placed
between the inverting input and an AC ground.
Figure 8. Compensation for Inverting Gains
RG
RC
VO
VI
CC
(OPTIONAL)
–
+
6300 F08
RF
=
–RF
RG
VO
VI
< 5MHz
1
2
πRCCC
(RC || RG) ≤ RF/9
RC
VO
VI
CC
(OPTIONAL)
+
–
6300 F09
RF
RG
= 1 +
RF
RG
VO
VI
< 5MHz
1
2
πRCCC
(RC || RG) ≤ RF/9
Figure 9. Compensation for Noninverting Gains
相关PDF资料 |
PDF描述 |
|---|---|
| VI-262-MX-F1 | CONVERTER MOD DC/DC 15V 75W |
| MS3100A22-13S | CONN RCPT 5POS WALL MNT W/SCKT |
| LT6300IGN#TR | IC XDSL LINE DRIVER 16-SSOP |
| VE-25P-IU-F2 | CONVERTER MOD DC/DC 13.8V 200W |
| VI-261-MX-F3 | CONVERTER MOD DC/DC 12V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT6301 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual 500mA, Differential xDSL Line Driver in 28-Lead TSSOP Package |
| LT6301CFE | 功能描述:IC XDSL LINE DRIVER DUAL 28TSSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| LT6301CFE#PBF | 功能描述:IC XDSL LINE DRIVER DUAL 28TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| LT6301CFE#TR | 功能描述:IC XDSL LINE DRIVER DUAL 28TSSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| LT6301CFE#TRPBF | 功能描述:IC XDSL LINE DRIVER DUAL 28TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。