- 您现在的位置：买卖IC网 > PDF目录14154 > LT8410EDC#TRPBF (Linear Technology)IC REG BOOST ADJ 8DFN PDF资料下载
参数资料
| 型号： | LT8410EDC#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST ADJ 8DFN |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.5 V ~ 40 V |
| 输入电压： | 2.5 V ~ 16 V |
| PWM 型： | 电流模式 |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-DFN（2x2） |
LT8410/LT8410-1
APPLICATIONS INFORMATION
or 0805 size capacitor will be adequate. A 0.1μF to 1μF
capacitor placed on the CAP node is recommended to filter
the inductor current, while a 0.1μF to 1μF capacitor placed
on the V OUT node will give excellent transient response
and stability. To make the V REF pin less sensitive to noise,
putting a capacitor on the V REF pin is recommended, but not
required. A 47nF to 220nF 0402 capacitor will be sufficient.
Table 2 shows a list of several capacitor manufacturers.
Consult the manufacturers for more detailed information
and for their entire selection of related parts.
Table 2. Recommended Ceramic Capacitor Manufacturers
MANUFACTURER PHONE WEB SITE
Taiyo Yuden (408) 573-4150 www.t-yuden.com
Murata (814) 237-1431 www.murata.com
Connecting the Load to the CAP Node
The efficiency of the converter can be improved by con-
necting the load to the CAP pin instead of the V OUT pin.
The power loss in the PMOS disconnect circuit is then
made negligible. No quiescent current will be consumed
in the internal feedback resistor divider string during
shutdown since the PMOS transistor will be open and the
internal feedback resistor divider is connected at the V OUT
pin. The disadvantage of this method is that the CAP node
cannot go to ground during shutdown, but will be limited
to around a diode drop below V CC . Loads connected to the
part should only sink current. Never force external power
supplies onto the CAP or V OUT pins.
AVX
(843) 448-9411
www.avxcorp.com
Maximum Output Load Current
V IN ? 150 ? 10 – 6
I PK = I LIMIT + mA
Kemet (408)986-0424 www.kemet.com
TDK (847) 803-6100 www.tdk.com
Setting Output Voltage
The output voltage is set by the FBP pin voltage. V OUT is
equal to 31.85 ? V FBP when the output is regulated, as
shown in Figure 1. Since the V REF pin provides a good
reference (1.235V), the FBP voltage can be easily set by
a resistor divider from the V REF pin to ground. The series
resistance of this resistor divider should be kept larger than
200KΩ to prevent loading down the V REF pin. The FBP pin
can also be biased directly by an external reference. For
overvoltage protection, the output voltage is limited to
40V. Therefore, if V FBP is higher than 1.235V, the output
voltage will stay at 40V.
50
40
30
20
10
The maximum output current of a particular LT8410 series
circuit is a function of several circuit variables. The following
method can be helpful in predicting the maximum load
current for a given circuit:
Step 1. Calculate the peak inductor current:
L
where I LIMIT is 25mA and 8mA for LT8410 and LT8410-1
respectively. L is the inductance value in henrys and V IN
is the input voltage to the boost circuit.
Step 2. Calculate the inductor ripple current:
I RIPPLE = ( V OUT + 1 – V IN ) ? 200 ? 10 – 6 mA
L
where V OUT is the desired output voltage. If the inductor
ripple current is less than the peak current, then the circuit
will only operate in discontinuous conduction mode. The
inductor value should be increased so that I RIPPLE < I PK .
An application circuit can be designed to operate only in
discontinuous mode, but the output current capability
will be reduced.
Step 3. Calculate the average input current:
0
0
0.5
1 1.5
FBP VOLTAGE (V)
2
8410-1 F01
I IN(AVG) = I PK –
I RIPPLE
2
mA
Figure 1. FBP to V OUT Transfer Curve
84101fb
9
相关PDF资料 |
PDF描述 |
|---|---|
| 12LRS156C | INDUCTOR RAD 15MH 95MA T/H 10X8 |
| MAX6866UK39D5S+T | IC MPU SUPERVISOR SOT23-5 |
| VI-J5T-CZ-F1 | CONVERTER MOD DC/DC 6.5V 25W |
| HMC12DRXS-S734 | CONN EDGECARD 24POS DIP .100 SLD |
| 12LRS153C | INDUCTOR RAD 15UH 3A T/H 10X8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT8410IDC#PBF | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Up 2.5V to 16V 8-Pin DFN EP |
| LT8410IDC#TRMPBF | 功能描述:IC REG BOOST ADJ 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LT8410IDC#TRPBF | 功能描述:IC REG BOOST ADJ 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LT8410IDC-1#PBF | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Up 2.5V to 16V 8-Pin DFN EP |
| LT8410IDC-1#TRMPBF | 功能描述:IC REG BOOST ADJ 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。