- 您现在的位置：买卖IC网 > PDF目录14110 > LT8410IDC#TRMPBF (Linear Technology)IC REG BOOST ADJ 8DFN PDF资料下载
参数资料
| 型号： | LT8410IDC#TRMPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST ADJ 8DFN |
| 标准包装： | 500 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.5 V ~ 40 V |
| 输入电压： | 2.5 V ~ 16 V |
| PWM 型： | 电流模式 |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-DFN（2x2） |
LT8410/LT8410-1
APPLICATIONS INFORMATION
I OUT(NOM) =
I IN(AVG) ? V IN ? 0.7
1.30 ? ? 1 +
CONNECT TO
Step4.Calculatethenominaloutputcurrent:
mA
V OUT
Step 5. Derate output current:
I OUT = I OUT(NOM) ? 0.8
For low output voltages the output current capability will
be increased. When using output disconnect (load current
taken from V OUT ), these higher currents will cause the
drop in the PMOS switch to be higher resulting in lower
output current capability than predicted by the preceding
equations.
Inrush Current
When V CC is stepped from ground to the operating voltage
while the output capacitor is discharged, a high level of
inrush current may flow through the inductor and Schottky
diode into the output capacitor. Conditions that increase
inrush current include a larger more abrupt voltage step
at V CC , a larger output capacitor tied to the CAP pin and
an inductor with a low saturation current. While the chip is
designed to handle such events, the inrush current should
not be allowed to exceed 0.3A. For circuits that use output
capacitor values within the recommended range and have
input voltages of less than 6V, inrush current remains low,
posing no hazard to the device. In cases where there are
large steps at V CC (more than 6V) and/or a large capacitor
is used at the CAP pin, inrush current should be measured
to ensure safe operation.
Soft-Start
The LT8410 series contains a soft-start circuit to limit
peak switch currents during start-up. High start-up cur-
rent is inherent in switching regulators, in general, since
the feedback loop is saturated due to V OUT being far from
its final value. The regulator tries to charge the output
capacitor as quickly as possible, which results in large
peak current.
When the FBP pin voltage is generated by a resistor divider
from the V REF pin, the start-up current can be limited by
connecting an external capacitor (typically 47nF to 220nF)
to the V REF pin. When the part is brought out of shutdown,
this capacitor is first discharged for about 70μs (providing
10
protection against pin glitches and slow ramping), then
an internal 10μA current source pulls the V REF pin slowly
to 1.235V. Since the V OUT voltage is set by the FBP pin
voltage, the V OUT voltage will also slowly increase to the
regulated voltage, which results in lower peak inductor
current. The voltage ramp rate on the pin can be set by
the value of the V REF pin capacitor.
Output Disconnect
The LT8410 series has an output disconnect PMOS that
blocks the load from the input during shutdown. The
maximum current through the PMOS is limited by circuitry
inside the chip, helping the chip survive output shorts.
SHDN Pin Comparator and Hysteresis Current
An internal comparator compares the SHDN pin voltage
with an internal voltage reference (1.3V) which gives a
precise turn-on voltage level. The internal hysteresis of this
turn-on voltage is about 60mV. When the chip is turned on,
and the SHDN pin voltage is close to this turn-on voltage,
0.1μA current flows out of the SHDN pin. This current is
called SHDN pin hysteresis current, and will go away when
the chip is off. By connecting the external resistors as in
Figure 2, a user-programmable enable voltage function
can be realized.
The turn-on voltage for the configuration is:
? R1 ?
?
? R2 ?
and the turn-off voltage is:
( 1.24 ? R3 ? 10 ? 7 ) ? ? ? ? 1 + R2 R1 ? ? ? ? (R1 ? 10 ? 7 )
where R1, R2 and R3 are resistance value in Ω.
ENABLE VOLTAGE
R1
R3
SHDN PIN
R2
84101 F02
Figure 2. Programming Enable Voltage by Using External Resistors
84101fb
相关PDF资料 |
PDF描述 |
|---|---|
| GBA35DTMT | CONN EDGECARD 70POS R/A .125 SLD |
| VI-BN4-EW-F1 | CONVERTER MOD DC/DC 48V 100W |
| LTC3459EDC#TRMPBF | IC REG BOOST SYNC ADJ 6DFN |
| MAX6868UK16D2L+T | IC MPU SUPERVISOR SOT23-5 |
| LQH6PPN100M43L | INDUCTOR POWER 10UH 2.6A 2424 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT8410IDC-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Ultralow Power Boost Converter with Output Disconnect |
| LT8415EDDB#TRMPBF | 功能描述:IC REG BOOST ADJ 25MA 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:升压（升压） 输出类型:两者兼有 输出数:1 输出电压:5V，2 V ~ 16.5 V 输入电压:2 V ~ 16.5 V PWM 型:- 频率 - 开关:45kHz 电流 - 输出:50mA 同步整流器:无 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 供应商设备封装:8-PDIP |
| LT8415EDDB#TRPBF | 功能描述:IC REG BOOST ADJ 25MA 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LT8415IDDB#TRMPBF | 功能描述:IC REG BOOST ADJ 25MA 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT8415IDDB#TRPBF | 功能描述:IC REG BOOST ADJ 25MA 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。