- 您现在的位置：买卖IC网 > PDF目录11022 > LTC1064-2CSW#TR (Linear Technology)IC FILTER LP 8ORD BTTWRTH 16SOIC PDF资料下载
参数资料
| 型号： | LTC1064-2CSW#TR |
| 厂商： | Linear Technology |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC FILTER LP 8ORD BTTWRTH 16SOIC |
| 标准包装： | 1,000 |
| 滤波器类型： | 巴特沃斯，低通开关电容器 |
| 频率 - 截止或中心： | 140kHz |
| 滤波器数： | 1 |
| 滤波器阶数： | 8th |
| 电源电压： | ±2.37 V ~ 8 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
LTC1064-2
7
10642fa
UU
U
PI FU CTIO S
NC (Pins 1, 6, 8 and 13): The “no connection” pins should
be preferably grounded. These pins are not internally
connected.
VIN, VOUT (Pins 2, 9): The input Pin 2 is connected to an
18k resistor tied to the inverting input of an op amp. Pin
2 is protected against static discharge. The device’s
output, Pin 9, is the output of an op amp which can
typically source/sink 3mA/1mA. Although the internal op
amps are unity gain stable, driving long coax cables is not
recommended.
When testing the device for noise and distortion, the
output, Pin 9, should be buffered. (Figure 1)
The op amp
power supply wire (or trace) should be connected
directly to the power source. To eliminate switching
transients from filter output, buffer filter output with a
third order lowpass (Figure 5).
AGND (Pins 3, 5): For dual supply operation these pins
should be connected to a ground plane. For single supply
operation both pins should be tied to one half supply,
(Figure 3).
V+, V– (Pins 4, 12): Should be bypassed with a 0.1F
capacitor to an adequate AGND. Low noise, nonswitching
power supplies are recommended.
To avoid latchup when
the power supplies exhibit high turn-on transients, a
1N5817 Schottky diode should be added from the V+ and
V– pins to ground (Figures 1, 2 and 3).
RIN A, OUT C (Pins 7, 14): A very short connection between
Pin 7 and Pin 14 is recommended. This connection should
be preferably done under the IC package. In a breadboard
use a one inch, or less, shielded coaxial cable: the shield
should be grounded. In a PC board, use a one inch trace or
less; surround the trace by a ground plane.
50/100 (Pin 10): The DC level at this pin determines the
ratio of clock frequency to the –3dB frequency of the filter.
The ratio is 50:1 when Pin 10 is at V+ and 100:1 when
Pin 10 is at V–. This pin should be bypassed with a 0.1F
capacitor to analog ground when it’s connected to V– or V+
(Figure 1). See Tables 1 through 7 for typical gain and delay
responses for the two ratios.
fCLK (Pin 11): For ±5V supplies the logic threshold level is
1.4V. For ±8V and 0V to 5V supplies the logic threshold
levels are 2.2V and 3V respectively. The logic threshold
levels vary ±100mV over the full military temperature
range. The recommended duty cycle of the input clock is
50% although for clock frequencies below 500kHz the
clock “on” time can be as low as 200ns. The maximum
clock frequency for ±5V supplies is 4MHz. For ±7V sup-
plies and above, the maximum clock frequency is 7MHz.
Do not allow the clock levels to exceed the power supplies.
For single supply operation ≥6V use level shifting at Pin 11
with T2L levels (Figure 4).
(Pin Numbers Refer to the 14-Pin Package)
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1064-7CSW#PBF | IC FILTR 8TH ORDR LOWPASS 16SOIC |
| VE-B0T-IY-F4 | CONVERTER MOD DC/DC 6.5V 50W |
| VE-J5V-IW-B1 | CONVERTER MOD DC/DC 5.8V 100W |
| VE-J50-IW-B1 | CONVERTER MOD DC/DC 5V 100W |
| LTC1064-7CSW | IC FILTR 8TH ORDR LOWPASS 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1064-2M | 制造商:LINER 制造商全称:Linear Technology 功能描述:Low Noise, High Frequency, 8th Order Butterworth Lowpass Filter |
| LTC1064-2MJ | 制造商:LINER 制造商全称:Linear Technology 功能描述:Low Noise, High Frequency, 8th Order Butterworth Lowpass Filter |
| LTC1064-2MJ/883 | 制造商:Linear Technology 功能描述:Active Filter Single Low Pass 8th Order 140kHz 14-Pin CDIP |
| LTC1064-2ML/883 | 制造商:Linear Technology 功能描述:Active Filter Single Low Pass 8th Order 140kHz |
| LTC1064-3 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Low Noise, High frequency,8th Order Linear Phase Lowpass Filter |
发布紧急采购，3分钟左右您将得到回复。