- 您现在的位置：买卖IC网 > PDF目录15286 > LTC1148CS-5 (Linear Technology)IC REG CTRLR BUCK PWM CM 14-SOIC PDF资料下载
参数资料
| 型号： | LTC1148CS-5 |
| 厂商： | Linear Technology |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 14-SOIC |
| 标准包装： | 55 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 250kHz |
| 占空比： | 100% |
| 电源电压： | 3.5 V ~ 18 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
LTC1148
LTC1148-3.3/LTC1148-5
APPLICATIO S I FOR ATIO
level threshold MOSFETs (V GS(TH) < 2.5V) are strongly
recommended. The LTC1148/LTC1148HV series supply
voltage must always be less than the absolute maximum
V GS ratings for the MOSFETs.
The maximum output current I MAX determines the R DS(ON)
requirement for the two MOSFETs. When the LTC1148
C IN and C OUT Selection
In continuous mode, the source of the P-channel MOSFET
is a square wave of duty cycle V OUT /V IN . To prevent large
voltage transients, a low ESR input capacitor sized for the
maximum RMS current must be used. The maximum
RMS capacitor current is given by:
series is operating in continuous mode, the simplifying
assumption can be made that one of the two MOSFETs is
always conducting the average load current. The duty
C IN Required I RMS ≈ I MAX
[V OUT (V IN – V OUT )] 1/2
V IN
P-Ch Duty Cycle = OUT
cycles for the two MOSFETs are given by:
V
V IN
This formula has a maximum at V IN = 2V OUT , where
I RMS = I OUT /2. This simple worst-case condition is com-
monly used for design because even significant devia-
tions do not offer much relief. Note that capacitor
N-Ch Duty Cycle =
( V IN – V OUT )
V IN
manufacturer’s ripple current ratings are often based on
only 2000 hours of life. This makes it advisable to further
derate the capacitor, or to choose a capacitor rated at a
From the duty cycles the required R DS(ON) for each MOS-
FET can be derived:
higher temperature than required. Always consult the
manufacturer if there is any question. An additional 0.1 μ F
P-Ch R DS(ON) =
N-Ch R DS(ON) =
V IN (P P )
V OUT (I MAX2 )(1 + δ P )
V IN (P N )
(V IN – V OUT )(I MAX2 )(1 + δ N )
to 1 μ F ceramic capacitor is also required on V IN Pin 3 for
high frequency decoupling.
The selection of C OUT is driven by the required effective
series resistance (ESR). The ESR of C OUT must be less
than twice the value of R SENSE for proper operation of the
LTC1148 series:
where P P and P N are the allowable power dissipations and
d P and d N are the temperature dependencies of R DS(ON) .
P P and P N will be determined by efficiency and/or thermal
requirements (see Efficiency Considerations). (1 + d) is
generally given for a MOSFET in the form of a normalized
R DS(ON) vs temperature curve, but d = 0.007/ ° C can be
used as an approximation for low voltage MOSFETs.
The Schottky diode D1 shown in Figure 1 only conducts
during the dead-time between the conduction of the two
power MOSFETs. D1’s sole purpose in life is to prevent the
body diode of the N-channel MOSFET from turning on and
storing charge during the dead time, which could cost as
much as 1% in efficiency (although there are no other
harmful effects if D1 is omitted). Therefore, D1 should be
selected for a forward voltage of less than 0.7V when
conducting I MAX .
C OUT Required ESR < 2R SENSE
Optimum efficiency is obtained by making the ESR equal
to R SENSE . As the ESR is increased up to 2R SENSE , the
efficiency degrades by less than 1%. If the ESR is greater
than 2R SENSE , the voltage ripple on the output capacitor
will prematurely trigger Burst Mode operation, resulting in
disruption of continuous mode and an efficiency hit which
can be several percent.
Manufacturers such as Nichicon and United Chemicon
should be considered for high performance capacitors.
The OS-CON semiconductor dielectric capacitor available
from Sanyo has the lowest ESR/size ratio of any aluminum
electrolytic at a somewhat higher price. Once the ESR
requirement for C OUT has been met, the RMS current
rating generally far exceeds the I RIPPLE(P-P) requirement.
114835fd
10
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B2Z-EX-F4 | CONVERTER MOD DC/DC 2V 30W |
| LTC1148CS-3.3#PBF | IC REG CTRLR BUCK PWM CM 14-SOIC |
| VI-B2Z-EX-F3 | CONVERTER MOD DC/DC 2V 30W |
| LTC1929CG-PG#TRPBF | IC REG CTRLR BUCK PWM CM 28-SSOP |
| VI-B2Z-EX-F1 | CONVERTER MOD DC/DC 2V 30W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1148CS-5#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 14-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC1148CS-5#TR | 功能描述:IC REG CTRLR BUCK PWM CM 14-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1148CS-5#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 14-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1148HV | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Synchronous Step-Down Switching Regulators |
| LTC1148HVCN | 功能描述:IC REG CTRLR BUCK PWM CM 14-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
发布紧急采购，3分钟左右您将得到回复。