- 您现在的位置：买卖IC网 > PDF目录11022 > LTC1164-5CN#PBF (Linear Technology)IC FILTR 8TH ORDER LOWPASS 14DIP PDF资料下载
参数资料
| 型号： | LTC1164-5CN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/16页 |
| 文件大小： | 0K |
| 描述： | IC FILTR 8TH ORDER LOWPASS 14DIP |
| 标准包装： | 25 |
| 滤波器类型： | 巴特沃斯或贝塞尔低通 |
| 频率 - 截止或中心： | 20kHz |
| 滤波器数： | 1 |
| 滤波器阶数： | 8th |
| 电源电压： | 4.75 V ~ 16 V，±2.375 V ~ 8 V |
| 安装类型： | 通孔 |
| 封装/外壳： | 14-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 14-PDIP |
| 包装： | 管件 |
LTC1164-5
8
11645fc
1
2
3
4
5
6
7
14
13
12
11
10
9
8
VIN
5V
≤ V+ ≤16V
1k
VOUT
DIGITAL SUPPLY
+
GND
CLOCK SOURCE
1164-5 F02
+
LTC1164-5
0.1
F
1
F
10k
1
2
3
4
5
6
7
14
13
12
11
10
9
8
VIN
V+
1k
V–
VOUT
LTC1164-5
DIGITAL SUPPLY
+
GND
CLOCK SOURCE
*
1164-5 F01
* OPTIONAL (SEE TEXT)
0.1
F
0.1
F
Power Supply (Pins 4, 12)
The V
+ (Pin4)andtheV–(Pin12)shouldbebypassedwith
a 0.1
F capacitor to an adequate analog ground. The
filter’s power supplies should be isolated from other
digital or high voltage analog supplies. A low noise linear
supply is recommended. Using a switching power supply
will lower the signal-to-noise ratio of the filter. The supply
during power-up should have a slew rate less than 1V/
s.
When V
+ is applied before V–, and V– can be more positive
than ground, a signal diode must be used to clamp V
–.
Figures 1 and 2 show typical connections for dual and
single supply operation.
Clock Input (Pin 11)
Any TTL or CMOS clock source with a square-wave output
and 50% duty cycle (
±10%) is an adequate clock source
for the device. The power supply for the clock source
should not be the filter’s power supply. The analog ground
for the filter should be connected to clock’s ground at a
single point only. Table 1 shows the clock’s low and high
level threshold value for a dual or single supply operation.
A pulse generator can be used as a clock source provided
the high level ON time is greater than 0.5
s.Sinewavesare
not recommended for clock input frequencies less than
100kHz, since excessively slow clock rise or fall times
generate internal clock jitter (maximum clock rise or fall
time
≤1s). The clock signal should be routed from the
right side of the IC package to avoid coupling into any input
or output analog signal path. A 1k resistor between clock
source and Pin 11 will slow down the rise and fall times of
the clock to further reduce charge coupling, Figures 1
and 2.
Table 1. Clock Source High and Low Threshold Levels
POWER SUPPLY
HIGH LEVEL
LOW LEVEL
Dual Supply >
±3.4V
≥ V+/3
≤ 0.5V
Dual Supply
≤ ±3.4V
≥ V+/3
≤ V – + 0.5V
Single Supply V
+ > 6.8V, V – = 0V
≥ V+ 0.65
≤ 0.5V + 1/2V+
Single Supply V
+ < 6.8V, V – = 0V
≥ V+/3
≤ 0.5V
Analog Ground (Pins 3, 5)
The filter performance depends on the quality of the
analog signal ground. For either dual or single supply
operation, an analog ground plane surrounding the pack-
age is recommended. The analog ground plane should be
connected to any digital ground at a single point. For dual
supply operation, Pins 3 and 5 should be connected to the
analog ground plane. For single supply operation Pins 3
and 5 should be biased at 1/2 supply and they should be
bypassed to the analog ground plane with at least a 1
F
capacitor (Figure 2). For single 5V operation at the highest
fCLK of 1MHz, Pins 3 and 5 should be biased at 2V. This
minimizes passband gain and phase variations (see Typi-
cal Performance Characteristics curves: Maximum Pass-
band for Single 5V, 50:1; and THD + Noise vs RMS Input
for Single 5V, 50:1).
PI FU CTIO S
UU
U
Figure 1. Dual Supply Operation for fCLK/fCUTOFF = 100:1
Figure 2. Single Supply Operation for fCLK/fCUTOFF = 100:1
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1164-6CN#PBF | IC FILTR 8TH ORDER LOWPASS 14DIP |
| LTC6602CUF#TRPBF | IC FILTER BANDPASS/LOWPASS 24QFN |
| LTC1061CSW#TRPBF | IC FILTR BUILDNG BLK TRPL 20SOIC |
| LTC1061CSW#TR | IC BUILDING BLK TRPL FLTR 20SOIC |
| LTC1061CSW#PBF | IC FILTR BUILDNG BLK TRPL 20SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1164-5CS | 制造商:LINER 制造商全称:Linear Technology 功能描述:Low Power 8th Order Pin Selectable Butterworth or Bessel Lowpass Filter |
| LTC1164-5CSW | 功能描述:IC FILTR 8TH ORDR LOWPASS 16SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| LTC1164-5CSW#PBF | 功能描述:IC FILTER 8TH ORD LOWPASS 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| LTC1164-5CSW#TR | 功能描述:IC FILTER LP 8TH ORDER 16SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| LTC1164-5CSW#TRPBF | 功能描述:IC FILTR 8TH ORDR LOWPASS 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。