- 您现在的位置：买卖IC网 > PDF目录97583 > LTC1232IN8#PBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 PDF资料下载
参数资料
| 型号： | LTC1232IN8#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 |
| 封装： | 0.300 INCH, PLASTIC, DIP-8 |
| 文件页数： | 6/8页 |
| 文件大小： | 97K |
| 代理商： | LTC1232IN8#PBF |
6
LTC1232
1232fa
active low for a minimum of 250ms from the moment the
push-button reset input is released from logic low level.
RST: RST is an Active High Logic Output. It is the inverse
of RST.
ST: Logic Input to Reset the Watchdog Timer. Driving ST
either high or low longer than the time-out period set by
the TD input, forces the reset outputs to active states for
a minimum of 250ms. The timer resets itself and begins to
time-out again with each high to low transition on the ST
input (see Figure 2).
PI FU CTIO S
UU
U
APPLICATIO S I FOR ATIO
WU
UU
Figure 1. Reset Active Time
RST: Open Drain Logic Output for P Reset Control.
The LTC1232 provides three ways to generate P reset.
First, when VCC falls below VCC trip point (4.75V with
TOL = GND and 4.5V with TOL = VCC), RST goes active low.
After VCC returns to 5V, the reset pulse generator forces
RST to remain active low for a minimum of 250ms.
Second, when the watchdog timer is not serviced prior to
a selected time-out period, the reset pulse generator also
forces RST to active low for a minimum of 250ms and
repeats for every time-out period. Third and the last, when
the PB RST pin stays active low for a minimum of 40ms,
RST becomes active low. The RST output will remain
The precision voltage comparator, C1, typically has 40mV
of hysteresis which ensures that glitches at VCC pin do not
activate the reset outputs. Response time is typically 10s.
To help prevent mitriggering due to transient loads, VCC
pin should be bypassed with a 0.1F capacitor with the
leads trimmed as short as possible.
Push-Button Reset
The LTC1232 provides a logic input pin, PB RST, for direct
connection to a push-button. This push-button reset input
requires an active low signal. Internally, this input signal is
debounced and timed for a minimum of 40ms. When this
Power Monitoring
The LTC1232 uses a bandgap voltage reference and a
precision voltage comparator, C1, to monitor the 5V
supply input on VCC (see Block Diagram). When VCC falls
below the VCC trip point (4.62V typical with
TOL = GND and 4.37V typical with TOL VCC), the reset
outputs are forced to active states. The VCC trip point
accounts for a 5% or 10% variation on VCC, so the reset
outputs become active when VCC falls below the VCC trip
point. On power-up, the reset signals are held in active
states for a minimum of 250ms after the VCC trip point is
reached to allow the power supply and microprocessor
to stabilize. On power-down, the RST signal remains
active low even with VCC as low as 1V. This capability helps
hold the microprocessor in stable shutdown condition.
Figure 1 shows the timing diagram of the RST signal.
V2
V1
V1 = VCC TRIP POINT
V2 = VCC TRIP POINT + VHYS
t1 = RESET ACTIVE TIME
t1
VCC
LTC1232 TA03
RST
t1
相关PDF资料 |
PDF描述 |
|---|---|
| LV2134V | PHASE LOCKED LOOP, 400 MHz, PDSO24 |
| LV5781 | SWITCHING REGULATOR, 225 kHz SWITCHING FREQ-MAX, PDSO14 |
| LV58063MX | SWITCHING REGULATOR, 444 kHz SWITCHING FREQ-MAX, PDSO8 |
| LV8014T | AC MOTOR CONTROLLER, 2.5 A, PDSO24 |
| LZ22291 | SPECIALTY ANALOG CIRCUIT, CDIP22 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1232IS8 | 功能描述:IC MPU SUPERVISORY CIRCUIT 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC1232IS8#PBF | 功能描述:IC MPU SUPERVISORY CIRCUIT 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 其它有关文件:STM6905 View All Specifications 标准包装:1 系列:- 类型:多压监控器 监视电压数目:5 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 140 ms 电压 - 阀值:2.188V，2.955V，可调，可调，可调 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-TSSOP 包装:Digi-Reel® 产品目录页面:1197 (CN2011-ZH PDF) 其它名称:497-8728-6 |
| LTC1232IS8#TR | 功能描述:IC MPU SUPERVISORY CIRCUIT 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC1232IS8#TRPBF | 功能描述:IC MPU SUPERVISORY CIRCUIT 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC1235CN | 功能描述:IC MPU SUPERVISORY CIRCUIT 16DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
发布紧急采购，3分钟左右您将得到回复。