- 您现在的位置：买卖IC网 > PDF目录10283 > LTC1286IS8 (Linear Technology)IC CONV A/D SAMPLING 12BIT 8SOIC PDF资料下载
参数资料
| 型号： | LTC1286IS8 |
| 厂商： | Linear Technology |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | IC CONV A/D SAMPLING 12BIT 8SOIC |
| 标准包装： | 100 |
| 位数： | 12 |
| 采样率（每秒）： | 12.5k |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 1.25mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，单极 |
14
LTC1286/LTC1298
Figure 5. Shutdown current with CS high is 1nA typically,
regardless of the clock. Shutdown current with CS = ground
varies from 1
A at 1kHz to 35A at 200kHz.
APPLICATION INFORMATION
WU
U
Clock Frequency
The maximum recommended clock frequency is 200kHz
for the LTC1286/LTC1298 running off a 5V supply. With
the supply voltage changing, the maximum clock fre-
quency for the devices also changes (see the typical curve
of Maximum Clock Rate vs Supply Voltage). If the maxi-
mum clock frequency is used, care must be taken to
ensure that the device converts correctly.
Mixed Supplies
It is possible to have a microprocessor running off a 5V
supply and communicate with the LTC1286 operating on
a 9V supply. The requirement to achieve this is that the
outputs of CS and CLK from the MPU have to be able to trip
the equivalent inputs of the LTC1286 and the output of
DOUT from the LTC1286 must be able to toggle the
equivalent input of the MPU (see typical curve of Digital
Input Logic Threshold vs Supply Voltage). With the
LTC1286 operating on a 9V supply, the output of DOUT may
go between 0V and 9V. The 9V output may damage the
MPU running off a 5V supply. The way to get around this
possibility is to have a resistor divider on DOUT (Figure 6)
and connect the center point to the MPU input. It should
be noted that to get full shutdown, the CS input of the
LTC1286 must be driven to the VCC voltage to keep the CS
input buffer from drawing current. An alternative is to
leave CS low after a conversion, clock data until DOUT
outputs zeros, and then stop the clock low.
DOUT Loading
Capacitive loading on the digital output can increase power
consumption. A 100pF capacitor on the DOUT pin can add
more than 50
A to the supply current at a 200kHz clock
frequency. An extra 50
A or so of current goes into
charging and discharging the load capacitor. The same
goes for digital lines driven at a high frequency by any logic.
The C
× V × f currents must be evaluated and the trouble-
some ones minimized.
OPERATING ON OTHER THAN 5V SUPPLIES (LTC1286)
The LTC1286 operates from 4.5V to 9V supplies and the
LTC1298 operates from a 5V supply. To operate the LTC1286
on other than 5V supplies a few things must be kept in
mind.
Input Logic Levels
The input logic levels of CS, CLK and DIN are made to meet
TTL on a 5V supply. When the supply voltage varies, the
input logic levels also change. For the LTC1286 to sample
and convert correctly, the digital inputs have to be in the
proper logical low and high levels relative to the operating
supply voltage (see typical curve of Digital Input Logic
Threshold vs Supply Voltage). If achieving micropower
consumption is desirable, the digital inputs must go rail-to-
rail between supply voltage and ground (see ACHIEVING
MICROPOWER PERFORMANCE section).
FREQUENCY (kHz)
1
0.002
SUPPLY
CURRENT
(A)
5
1
0
15
20
25
35
20
100
140
LT1286/98 G01
10
30
80
180 200
40 60
120
160
CS = 0
(AFTER CONVERSION)
TA = 25°C
VCC = VREF = 5V
CS = VCC
+IN
–IN
GND
VCC
CLK
DOUT
VREF
50k
5V
4.7
F
MPU
(e.g. 8051)
5V
P1.4
P1.3
P1.2
LTC1286/98 F06
DIFFERENTIAL INPUTS
COMMON-MODE RANGE
0V TO 5V
9V
LTC1286
CS
Figure 6. Interfacing a 9V Powered LTC1286 to a 5V System
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/20WG75BA | CONN HSG RCPT 4POS WALL MT SCKT |
| VE-2NP-MY | CONVERTER MOD DC/DC 13.8V 50W |
| D38999/20JJ29PNLC | CONN HSG RCPT 29POS WALL MT PINS |
| D38999/24FG11PBLC | CONN HSG RCPT 11POS JAM NUT PINS |
| LTC1298IS8 | IC A/D CONV SAMPLING 12BIT 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1286IS8#PBF | 功能描述:IC CONV A/D SAMPLING 12BIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC1286IS8#TR | 功能描述:IC ADC 12BIT SAMPL MCRPWR 8SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1286IS8#TRPBF | 功能描述:IC CONV A/D SAMPLING 12BIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1286IS8PBF | 制造商:Linear Technology 功能描述:ADC SAR 12.5ksps 12-Bit Serial SOIC8 |
| LTC1287-4ISW | 制造商:Linear Technology 功能描述: |
发布紧急采购，3分钟左右您将得到回复。