- 您现在的位置：买卖IC网 > PDF目录2003 > LTC1288IS8#TRPBF (Linear Technology)IC A/D CONV SAMPLING 12BIT 8SOIC PDF资料下载
参数资料
| 型号： | LTC1288IS8#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/24页 |
| 文件大小： | 0K |
| 描述： | IC A/D CONV SAMPLING 12BIT 8SOIC |
| 标准包装： | 2,500 |
| 位数： | 12 |
| 采样率（每秒）： | 6.6k |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 630µW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 2 个单端，单极 |
16
LTC1285/LTC1288
APPLICATION INFORMATION
WU
U
Single-Ended Inputs
The sample-and-hold of the LTC1288 allows conversion
of rapidly varying signals. The input voltage is sampled
during the tSMPL time as shown in Figure 7. The sampling
interval begins as the bit preceding the MSBF bit is shifted
in and continues until the falling CLK edge after the MSBF
bit is received. On this falling edge, the S&H goes into hold
mode and the conversion begins.
Differential Inputs
With differential inputs, the ADC no longer converts just a
single voltage but rather the difference between two volt-
ages. In this case, the voltage on the selected “+” input is
still sampled and held and therefore may be rapidly time
varying just as in single-ended mode. However, the volt-
age on the selected “–” input must remain constant and be
free of noise and ripple throughout the conversion time.
Otherwise, the differencing operation may not be per-
formed accurately. The conversion time is 12 CLK cycles.
Therefore, a change in the “–” input voltage during this
interval can cause conversion errors. For a sinusoidal
voltage on the “–” input this error would be:
VERROR (MAX) = VPEAK × 2 × π × f(“–”) × 12/fCLK
Where f(“–”) is the frequency of the “–” input voltage,
VPEAK is its peak amplitude and fCLK is the frequency of the
CLK. In most cases VERROR will not be significant. For a
60Hz signal on the “–” input to generate a 1/4LSB error
(152
V) with the converter running at CLK = 120kHz, its
peak value would have to be 4.03mV.
ANALOG INPUTS
Because of the capacitive redistribution A/D conversion
techniques used, the analog inputs of the LTC1285/
LTC1288 have capacitive switching input current spikes.
These current spikes settle quickly and do not cause a
problem. However, if large source resistances are used or
if slow settling op amps drive the inputs, care must be
taken to insure that the transients caused by the current
spikes settle completely before the conversion begins.
“+” Input Settling
The input capacitor of the LTC1285 is switched onto “+”
input during the tSMPL time (see Figure 1) and samples
the input signal within that time. However, the input
capacitor of the LTC1288 is switched onto “+” input
during the sample phase (tSMPL, see Figure 7). The
sample phase is 1 1/2 CLK cycles before conversion
starts. The voltage on the “+” input must settle com-
pletely within tSMPLE for the LTC1285 and the LTC1288
respectively. Minimizing RSOURCE+ and C1 will improve
the input settling time. If a large “+” input source resis-
tance must be used, the sample time can be increased by
using a slower CLK frequency.
“–” Input Settling
At the end of the tSMPL, the input capacitor switches to the
“–” input and conversion starts (see Figures 1 and 7).
During the conversion, the “+” input voltage is effectively
“held” by the sample-and-hold and will not affect the
conversion result. However, it is critical that the “–” input
voltage settles completely during the first CLK cycle of the
conversion time and be free of noise. Minimizing RSOURCE
–
and C2 will improve settling time. If a large “–” input
source resistance must be used, the time allowed for
settling can be extended by using a slower CLK frequency.
Input Op Amps
When driving the analog inputs with an op amp it is
important that the op amp settle within the allowed time
(see Figure 7). Again, the“+” and “–” input sampling times
can be extended as described above to accommodate
slower op amps. Most op amps, including the LT1006 and
LT1413 single supply op amps, can be made to settle well
even with the minimum settling windows of 12.5
s (“+”
input) which occur at the maximum clock rate of 120kHz.
Source Resistance
The analog inputs of the LTC1285/LTC1288 look like a
20pF capacitor (CIN) in series with a 500 resistor (RON)
as shown in Figure 8. CIN gets switched between the
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1298IS8#TRPBF | IC A/D CONV SAMPLING 12BIT 8SOIC |
| LTC1327CNW#PBF | IC TXRX EIA/TIA-562 3.3V 28-DIP |
| LTC1329ACS8-50#TRPBF | IC D/A CONV 8BIT MICROPWR 8-SOIC |
| LTC1337CNW#PBF | IC 3DVR/5RCVR 5V RS232 28-DIP |
| LTC1382IN#PBF | IC TXRX 5V RS232 W/SHTDWN 18-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1289BCN | 功能描述:IC DATA ACQ SYS 12BIT 3V 20-DIP RoHS:否 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| LTC1289BCN#PBF | 功能描述:IC DATA ACQ SYS 12BIT 3V 20-DIP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| LTC1289BCSW | 功能描述:IC DATA ACQ SYS 12BIT 3V 20-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| LTC1289BCSW#PBF | 功能描述:IC DATA ACQ SYS 12BIT 3V 20-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| LTC1289BCSW#TR | 功能描述:IC DATA ACQ SYS 12BIT 3V 20SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。