- 您现在的位置：买卖IC网 > PDF目录179917 > LTC1402IGN#TRPBF (LINEAR TECHNOLOGY CORP) Serial 12-Bit, 2.2Msps Sampling ADC with Shutdown; Package: SSOP; No of Pins: 16; Temperature Range: -40°C to +85°C PDF资料下载
参数资料
| 型号： | LTC1402IGN#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | ADC |
| 英文描述： | Serial 12-Bit, 2.2Msps Sampling ADC with Shutdown; Package: SSOP; No of Pins: 16; Temperature Range: -40°C to +85°C |
| 中文描述： | 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| 封装： | 0.150 INCH, PLASTIC, SSOP-16 |
| 文件页数： | 3/24页 |
| 文件大小： | 280K |
| 代理商： | LTC1402IGN#TRPBF |
11
LTC1402
APPLICATIONS INFORMATION
WU
U
less susceptible to both problems. When high amplitude
unwanted signals are close in frequency to the desired signal
frequency, a multiple pole filter is required. Figure 3 shows
a simple implementation using an LTC1560-1, a fifth order
elliptic continuous-time 1MHz filter.
BIPOLAR AND UNIPOLAR INPUT RANGES
The
±2V bipolar input range of the LTC1402 is optimized
for low noise and low distortion. Most op amps also
perform best over this same range, allowing direct cou-
pling to the analog inputs and eliminating the need for
special translation circuitry. The inputs of the LTC1402
may also be driven fully differential in bipolar mode with
a single supply. Each input should not swing more than
2VP-P individually to get the best performance from single
supply amplifiers.
The 0V to 4V range is ideal for single ended input use with
single supply applications.
LTC1402
AIN
+
AIN
–
VREF
AGND1
AGND2
GAIN
1402 F02
3
4
2
6
5
7
10
F
68pF
51
ANALOG
INPUT
Figure 2. RC Input Filter
LTC1560-1
1
2
3
4
8
7
6
5
0.1
F
5V
0.1
F
–5V
VIN
LTC1402
AIN
+
AIN
–
VREF
AGND1
AGND2
GAIN
1402 F03
3
4
2
6
5
7
10
F
Figure 3. 1MHz Fifth Order Elliptic Lowpass Filter
LT1630: Dual 30MHz Rail-to-Rail Voltage FB Amplifier.
2.7V to
±15V supplies. Very high AVOL, 500V offset and
520ns settling to 0.5LSB for a 4V swing. THD and noise
are – 93dB to 40kHz and below 1LSB to 320kHz (AV = 1,
2VP-P into 1k, VS = 5V), making the part excellent for AC
applications (to 1/3 Nyquist) where rail-to-rail perfor-
mance is desired. Quad version is available as LT1631.
LT1632: Dual 45MHz Rail-to-Rail Voltage FB Amplifier.
2.7V to
±15V supplies. Very high AVOL, 1.5mV offset and
400ns settling to 0.5LSB for a 4V swing. It is suitable for
applications with a single 5V supply. THD and noise are
– 93dB to 40kHz and below 1LSB to 800kHz (AV = 1,
2VP-P into 1k, VS = 5V), making the part excellent for AC
applications where rail-to-rail performance is desired.
Quad version is available as LT1633.
LT1813: Dual 100MHz 750V/
s 3mA Voltage Feedback
Amplifier. 5V to
±5V supplies. Distortion is – 86dB to
100kHz and – 77dB to 1MHz with
±5V supplies (2VP-P into
500
). Excellent part for fast AC applications with
±5V supplies.
INPUT FILTERING AND SOURCE IMPEDANCE
The noise and the distortion of the input amplifier and
other circuitry must be considered since they will add to
the LTC1402 noise and distortion. The small-signal band-
width of the sample-and-hold circuit is 80MHz. Any noise
or distortion products that are present at the analog inputs
will be summed over this entire bandwidth. Noisy input
circuitry should be filtered prior to the analog inputs to
minimize noise. A simple 1-pole RC filter is sufficient for
many applications. For example, Figure 2 shows a 68pF
capacitor from AIN+ to ground and a 51 source resistor
to limit the input bandwidth to 47MHz. The 68pF capacitor
also acts as a charge reservoir for the input sample-and-
hold and isolates the ADC input from sampling glitch-
sensitive circuitry.
High quality capacitors and resistors should be used since
these components can add distortion. NPO and silver mica
type dielectric capacitors have excellent linearity.
Carbon surface mount resistors can generate distortion
from self heating and from damage that may occur during
soldering. Metal film surface mount resistors are much
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1403ACMSE-1#PBF | Serial 12-Bit, 2.8Msps Sampling ADCs with Shutdown; Package: MSOP; No of Pins: 10; Temperature Range: 0°C to +70°C |
| LTC1403ACMSE-1#TRPBF | Serial 12-Bit, 2.8Msps Sampling ADCs with Shutdown; Package: MSOP; No of Pins: 10; Temperature Range: 0°C to +70°C |
| LTC1403AIMSE-1#PBF | Serial 12-Bit, 2.8Msps Sampling ADCs with Shutdown; Package: MSOP; No of Pins: 10; Temperature Range: -40°C to +85°C |
| LTC1403AIMSE-1#TRPBF | Serial 12-Bit, 2.8Msps Sampling ADCs with Shutdown; Package: MSOP; No of Pins: 10; Temperature Range: -40°C to +85°C |
| LTC1403CMSE-1#PBF | Serial 12-Bit, 2.8Msps Sampling ADCs with Shutdown; Package: MSOP; No of Pins: 10; Temperature Range: 0°C to +70°C |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1403ACMSE | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1403ACMSE#PBF | 功能描述:IC ADC 14BIT 2.8MSPS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC1403ACMSE#PBF | 制造商:Linear Technology 功能描述:ADC, 14BIT, 2.8MSPS, MSOP-10 |
| LTC1403ACMSE#TR | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1403ACMSE#TRPBF | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。