- 您现在的位置：买卖IC网 > PDF目录10261 > LTC1403ACMSE-1 (Linear Technology)IC ADC 14BIT 2.8MSPS DIFF 10MSOP PDF资料下载
参数资料
| 型号： | LTC1403ACMSE-1 |
| 厂商： | Linear Technology |
| 文件页数： | 6/22页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 2.8MSPS DIFF 10MSOP |
| 标准包装： | 50 |
| 位数： | 14 |
| 采样率（每秒）： | 2.8M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 12mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 10-MSOP 裸露焊盘 |
| 包装： | 管件 |
| 输入数目和类型： | 2 个单端，单极；1 个差分，单极 |
| 配用： | DC1082A-D-ND - BOARD SAR ADC LTC1403A DC1082A-C-ND - BOARD SAR ADC LTC1403A-1 |
LTC1403-1/LTC1403A-1
14
14031fc
APPLICATIONS INFORMATION
Board Layout and Bypassing
Wire wrap boards are not recommended for high resolu-
tion and/or high speed A/D converters. To obtain the best
performance from the LTC1403-1/LTC1403A-1, a printed
circuit board with ground plane is required. Layout for
the printed circuit board should ensure that digital and
analog signal lines are separated as much as possible.
In particular, care should be taken not to run any digital
track alongside an analog signal track. If optimum phase
match between the inputs is desired, the length of the two
input wires should be kept matched.
High quality tantalum and ceramic bypass capacitors
should be used at the VDD and VREF pins as shown in the
Block Diagram on the first page of this data sheet. For op-
timum performance, a 10F surface mount AVX capacitor
with a 0.1F ceramic is recommended for the VDDandVREF
pins. Alternatively, 10F ceramic chip capacitors such as
Murata GRM219R60J106M may be used. The capacitors
mustbelocatedasclosetothepinsaspossible.Thetraces
connecting the pins and the bypass capacitors must be
kept short and should be made as wide as possible.
Figure7showstherecommendedsystemgroundconnec-
tions. All analog circuitry grounds should be terminated at
the LTC1403-1/LTC1403A-1 GND (Pins 4, 5, 6 and exposed
pad). The ground return from the LTC1403-1/LTC1403A-1
(Pins 4, 5, 6 and exposed pad) to the power supply
should be low impedance for noise free operation. Digital
circuitry grounds must be connected to the digital supply
common. In applications where the ADC data outputs and
control signals are connected to a continuously active
microprocessor bus, it is possible to get errors in the
conversion results. These errors are due to feedthrough
from the microprocessor to the successive approximation
comparator. The problem can be eliminated by forcing the
microprocessor into a Wait state during conversion or by
using three-state buffers to isolate the ADC data bus.
POWER-DOWN MODES
Upon power-up, the LTC1403-1/LTC1403A-1 is initialized
to the active state and is ready for conversion. The Nap
and Sleep mode waveforms show the power-down modes
for the LTC1403-1/LTC1403A-1. The SCK and CONV inputs
control the power-down modes (see Timing Diagrams).
Two rising edges at CONV, without any intervening ris-
ing edges at SCK, put the LTC1403-1/LTC1403A-1 in Nap
mode and the power drain drops from 14mW to 6mW.
The internal reference remains powered in Nap mode.
Figure 7. Recommended Layout
14031 F07
FREQUENCY (Hz)
MAGNITUDE
(dB)
–60
–30
–20
14031 F06b
–70
–80
–120
–100
0
–10
–40
–50
–90
–110
0
371k
185k
556k
741k
Figure 6b. LTC1403-1 6MHz Sine Wave 4096 Point FFT Plot
with the LT1819 Driving the Inputs Differentially
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/26KE6AN | CONN HSG PLUG 6POS STRGHT PINS |
| LTC1407ACMSE-1 | IC ADC 14BIT 3MSPS SAMPLE 10MSOP |
| MS27472E8F6PA | CONN RCPT 6POS WALL MT W/PINS |
| D38999/26JJ4SNLC | CONN HSG PLUG 56POS STRGHT SCKT |
| LTC1403ACMSE | IC ADC 14BIT 2.8MSPS DIFF 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1403ACMSE-1#PBF | 功能描述:IC ADC 14BIT 2.8MSPS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC1403ACMSE-1#TR | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1403ACMSE-1#TRPBF | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1403ACMSEPBF | 制造商:Linear Technology 功能描述:ADC,LTC1403A 14bit 2.8MSPS SPI MSOP |
| LTC1403AHMSE | 制造商:Linear Technology 功能描述:ADC Single SAR 2.8Msps 14-bit Serial 10-Pin MSOP EP |
发布紧急采购，3分钟左右您将得到回复。