- 您现在的位置：买卖IC网 > PDF目录10667 > LTC1403AIMSE#PBF (Linear Technology)IC ADC 14BIT 2.8MSPS 10-MSOP PDF资料下载
参数资料
| 型号： | LTC1403AIMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 2/20页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 2.8MSPS 10-MSOP |
| 标准包装： | 50 |
| 位数： | 14 |
| 采样率（每秒）： | 2.8M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 12mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 10-MSOP 裸露焊盘 |
| 包装： | 管件 |
| 输入数目和类型： | 2 个单端，单极；1 个差分，单极 |
| 产品目录页面： | 1346 (CN2011-ZH PDF) |
| 配用： | DC1082A-D-ND - BOARD SAR ADC LTC1403A DC1082A-C-ND - BOARD SAR ADC LTC1403A-1 |
LTC1403/LTC1403A
10
1403fb
APPLICATIONS INFORMATION
10
μF
11
3
AIN
–
LTC1403/
LTC1403A
AIN
+
47pF
2
1
51
Ω
GND
VREF
1403A F01
Figure 1. RC Input Filter
INPUT FILTERING AND SOURCE IMPEDANCE
The noise and the distortion of the input amplier and other
circuitry must be considered since they will add to the
LTC1403/LTC1403A noise and distortion. The small-signal
bandwidth of the sample-and-hold circuit is 50MHz. Any
noise or distortion products that are present at the analog
inputs will be summed over this entire bandwidth. Noisy
input circuitry should be ltered prior to the analog inputs
to minimize noise. A simple 1-pole RC lter is sufcient for
many applications. For example, Figure 1 shows a 47pF
capacitor from AIN+ to ground and a 51Ω source resistor to
limit the input bandwidth to 47MHz. The 47pF capacitor also
acts as a charge reservoir for the input sample-and-hold
and isolates the ADC input from sampling-glitch sensitive
circuitry. High quality capacitors and resistors should be
used since these components can add distortion. NPO
and silvermica type dielectric capacitors have excellent
linearity. Carbon surface mount resistors can generate
distortion from self heating and from damage that may
occur during soldering. Metal lm surface mount resistors
are much less susceptible to both problems. When high
amplitude unwanted signals are close in frequency to the
desired signal frequency, a multiple pole lter is required.
High external source resistance, combined with the 13pF of
input capacitance, will reduce the rated 50MHz bandwidth
and increase acquisition time beyond 39ns.
INPUT RANGE
The analog inputs of the LTC1403/LTC1403A may be
driven fully differentially with a single supply. Each input
may swing up to 3VP-P individually. In the conversion
range, the noninverting input of each channel is always
up to 2.5V more positive than the inverting input of each
channel. The 0V to 2.5V range is also ideally suited for
single-ended input use with single supply applications. The
common mode range of the inputs extend from ground
to the supply voltage VDD. If the difference between the
AIN+ and AIN– inputs exceeds 2.5V, the output code will
stay xed at all ones and if this difference goes below 0V,
the ouput code will stay xed at all zeros.
INTERNAL REFERENCE
The LTC1403/LTC1403A has an on-chip, temperature
compensated, bandgap reference that is factory trimmed
near 2.5V to obtain 2.5V input span. The reference amplier
output VREF, (Pin 3) must be bypassed with a capacitor to
ground. The reference amplier is stable with capacitors
of 1μF or greater. For the best noise performance, a 10μF
ceramic or a 10μF tantalum in parallel with a 0.1μF ceramic
is recommended. The VREF pin can be overdriven with an
external reference as shown in Figure 2. The voltage of
the external reference must be higher than the 2.5V of the
class A pull-up output of the internal reference. The recom-
mended range for an external reference is 2.55V to VDD.
An external reference at 2.55V will see a DC quiescent load
of 0.75mA and as much as 3mA during conversion.
GND
LTC1403/
LTC1403A
VREF
10
μF
11
3
3VREF
1403A F02
Figure 2
相关PDF资料 |
PDF描述 |
|---|---|
| AD7658BSTZ | IC ADC 12BIT 6CH 250KSPS 64LQFP |
| AD7767BRUZ-1 | ADC 24BIT 64KSPS SAR 16-TSSOP |
| AD7714YRUZ | IC ADC SIGNAL COND 3/5V 24-TSSOP |
| LTC2446IUHF#PBF | IC ADC 24BIT 8CH HI SPEED 38QFN |
| LTC2448IUHF#PBF | IC ADC 24BIT HI SPEED 38QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1403CMSE | 功能描述:IC ADC 12BIT 2.8MSPS DIFF 10MSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1403CMSE#PBF | 功能描述:IC ADC 12BIT 2.8MSPS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC1403CMSE#TR | 功能描述:IC ADC 12BIT 2.8MSPS DIFF 10MSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1403CMSE#TRPBF | 功能描述:IC ADC 12BIT 2.8MSPS DIFF 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1403CMSE-1 | 功能描述:IC ADC 12BIT 2.8MSPS DIFF 10MSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。