- 您现在的位置：买卖IC网 > PDF目录10225 > LTC1410ISW#TR (Linear Technology)IC ADC 12BIT 1.25MSPS SMP 28SOIC PDF资料下载
参数资料
| 型号： | LTC1410ISW#TR |
| 厂商： | Linear Technology |
| 文件页数： | 5/16页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 1.25MSPS SMP 28SOIC |
| 标准包装： | 1,000 |
| 位数： | 12 |
| 采样率（每秒）： | 1.25M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 230mW |
| 电压电源： | 双 ± |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 2 个单端，双极；1 个差分，双极 |
13
LTC1410
APPLICATIONS INFORMATION
WU
U
Power Shutdown
The LTC1410 provides two power shutdown modes, Nap
and Sleep, to save power during inactive periods. The
Nap mode reduces the power by 95% and leaves only the
digital logic and reference powered up. The wake-up time
from Nap to active is 200ns. In Sleep mode all bias
currents are shut down and only leakage current re-
mains –– about 1
A. Wake-up time from Sleep mode is
t3
NAP/SLP
SHDN
1410 F12a
Figure 12a. NAP/SLP to SHDN Timing
Figure 12b. SHDN to CONVST Wake-Up Timing
much slower since the reference circuit must power up
and settle to 0.01% for full 12-bit accuracy. Sleep mode
wake-up time is dependent on the value of the capacitor
connected to the REFCOMP (Pin 4). The wake-up time is
10ms with the recommended 10
F capacitor.
Shutdown is controlled by Pin 21 (SHDN), the ADC is in
shutdown when it is low. The shutdown mode is selected
with Pin 20 (NAP/SLP); high selects Nap.
t2
t1
CS
CONVST
RD
1410 F12
t4
SHDN
CONVST
1410 F12b
Figure 13. CS to CONVST Setup Timing
Timing and Control
Conversion start and data read operations are controlled
by three digital inputs: CONVST, CS and RD. A logic “0”
applied to the CONVST pin will start a conversion after the
ADC has been selected (i.e., CS is low). Once initiated, it
cannot be restarted until the conversion is complete.
Converter status is indicated by the BUSY output. BUSY
is low during a conversion.
Figures 14 through 18 show several different modes of
operation. In modes 1a and 1b (Figures 14 and 15) CS
and RD are both tied low. The falling edge of CONVST
starts the conversion. The data outputs are always enabled
and data can be latched with the BUSY rising edge. Mode
1a shows operation with a narrow logic low CONVST
pulse. Mode 1b shows a narrow logic high CONVST pulse.
In mode 2 (Figure 16) CS is tied low. The falling edge of
CONVST signal again starts the conversion. Data outputs
are in three-state until read by the MPU with the RD signal.
Mode 2 can be used for operation with a shared MPU
databus.
In slow memory and ROM modes (Figures 17 and 18) CS
is tied low and CONVST and RD are tied together. The MPU
starts the conversion and reads the output with the RD
signal. Conversions are started by the MPU or DSP (no
external sample clock).
In slow memory mode the processor applies a logic low to
RD (= CONVST), starting the conversion. BUSY goes low
forcing the processor into a wait state. The previous
conversion result appears on the data outputs. When the
conversion is complete, the new conversion results ap-
pear on the data outputs; BUSY goes high releasing the
processor and the processor takes RD (= CONVST) back
high and reads the new conversion data.
In ROM mode, the processor takes RD (= CONVST) low,
starting a conversion and reading the previous conversion
result. After the conversion is complete, the processor can
read the new result and initiate another conversion.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27656E11B4SB | CONN RCPT 4POS WALL MNT W/SCKT |
| MS27484T8A44S | CONN PLUG 4POS STRAIGHT W/SCKT |
| ADM4851ARZ-REEL7 | IC TXRX RS485/422 500KBPS 8-SOIC |
| C091 31C006 100 2 | CONN MALE RCPT 6POS REAR MT |
| ADM4853ARZ-REEL7 | IC TXRX RS485/422 10MBPS 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1411CG | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC1411CG#PBF | 功能描述:IC ADC 14BIT 2.5MSPS 36SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC1411CG#TR | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC1411CG#TRPBF | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC1411IG | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。