- 您现在的位置：买卖IC网 > PDF目录10142 > LTC1411CG (Linear Technology)IC A/D CONV 14BIT 2.5MSPS 36SSOP PDF资料下载
参数资料
| 型号： | LTC1411CG |
| 厂商： | Linear Technology |
| 文件页数： | 2/16页 |
| 文件大小： | 0K |
| 描述： | IC A/D CONV 14BIT 2.5MSPS 36SSOP |
| 标准包装： | 37 |
| 位数： | 14 |
| 采样率（每秒）： | 2.5M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 325mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 36-SSOP |
| 包装： | 管件 |
| 输入数目和类型： | 2 个单端，双极；1 个差分，双极 |
10
LTC1411
1411f
the sampling capacitor, choose an amplifier that has a low
output impedance (<100
) at the closed-loop bandwidth
frequency. For example, if an amplifier is used in a gain of
1 and has a unity-gain bandwidth of 50MHz, then the
output impedance at 50MHz must be less than 100
. The
second requirement is that the closed-loop bandwidth
must be greater than 40MHz to ensure adequate small-
signal settling for full throughput rate. If slower op amps
are used, more settling time can be provided by increasing
the time between conversions.
The best choice for an op amp to drive the LTC1411 will
depend on the application. Generally applications fall into
two categories: AC applications where dynamic specifica-
tions are most critical and time domain applications where
DC accuracy and settling time are most critical. The
following list is a summary of the op amps that are suitable
for driving the LTC1411. More detailed information is
available in the Linear Technology Databooks and on the
LinearView
TM CD-ROM.
LT
1227: 140MHz Video Current Feedback Amplifier.
10mA supply current.
±5V to ±15V supplies. Low noise.
Good for AC applications.
LT1395: 400MHz Current Feedback Amplifier. Single 5V
or
±5V supplies. Good for AC applications.
LT1800: 80MHz, 25V/
sLowPowerRail-to-RailInputand
Output Precision Op Amp. Specified at 3V, 5V and
±5V
supplies. Excellent DC performance.
Peak Harmonic or Spurious Noise
The peak harmonic or spurious noise is the largest spec-
tral component excluding the input signal and DC. This
value is expressed in dB relative to the RMS value of a full-
scale input signal.
Full-Power and Full-Linear Bandwidth
The full-power bandwidth is that input frequency at which
the amplitude of the reconstructed fundamental is re-
duced by 3db for a full-scale input signal.
The full-linear bandwidth is the input frequency at which
the S/(N + D) has dropped to 74dB (12 effective bits). The
LTC1411 has been designed to optimize input bandwidth,
allowing the ADC to undersample input signals with fre-
quencies above the converter’s Nyquist frequency. The
noise floor stays very low at high frequencies; S/(N + D)
becomes dominated by distortion at frequencies far be-
yond Nyquist.
Driving the Analog Input
The differential analog inputs of the LTC1411 are easy to
drive. The inputs may be driven differentially or as a single-
ended input (i.e., the AIN– input is tied to a fixed DC voltage
such as the REFOUT pin of the LTC1411 or an external
source). Figure 1 shows a simplified block diagram for the
analog inputs of the LTC1411. The AIN+ and AIN– are
sampled at the same instant. Any unwanted signal that is
common mode to both inputs will be reduced by the
common mode rejection of the sample-and-hold circuit.
The inputs draw only one small current spike while charg-
ing the sample-and-hold capacitors at the end of conver-
sion. During conversion, the analog inputs draw only a
small leakage current. If the source impedance of the
driving circuits is low, then the LTC1411 inputs can be
driven directly. More acquisition time should be allowed
for a higher impedance source. Figure 5 shows the acqui-
sition time versus source resistance.
Choosing an Input Amplifier
Choosing an input amplifier is easy if a few requirements
are taken into consideration. First, to limit the magnitude
of the voltage spike seen by the amplifier from charging
APPLICATIO S I FOR ATIO
WU
UU
SOURCE RESISTANCE (
)
1
ACQUISITION
TIME
(
s)
1
10
10000
1411 G16
0.1
0.01
10
100
1000
100000
100
Figure 5. Acquisition Time vs Source Resistance
LinearView is a trademark of Linear Technology Corporation.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1690IN8 | IC RCVR/DVR PAIR LOW PWR 8-DIP |
| MS3102R18-1SX | CONN RCPT 10POS BOX MNT W/SCKT |
| VI-22H-IW-F1 | CONVERTER MOD DC/DC 52V 100W |
| IDT7200L35SO | IC MEM FIFO 256X9 35NS 28-SOIC |
| MS3100A16S-6P | CONN RCPT 3POS WALL MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1411CG#PBF | 功能描述:IC ADC 14BIT 2.5MSPS 36SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC1411CG#TR | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC1411CG#TRPBF | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC1411IG | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC1411IG#PBF | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
发布紧急采购，3分钟左右您将得到回复。