- 您现在的位置：买卖IC网 > PDF目录10175 > LTC1414CGN (Linear Technology)IC A/D CONV 14BIT SAMPLNG 28SSOP PDF资料下载
参数资料
| 型号： | LTC1414CGN |
| 厂商： | Linear Technology |
| 文件页数： | 2/20页 |
| 文件大小： | 0K |
| 描述： | IC A/D CONV 14BIT SAMPLNG 28SSOP |
| 标准包装： | 49 |
| 位数： | 14 |
| 采样率（每秒）： | 2.2M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 230mW |
| 电压电源： | 双 ± |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
| 输入数目和类型： | 2 个单端，双极；1 个差分，双极 |
10
LTC1414
APPLICATIONS INFORMATION
WU
U
Choosing an Input Amplifier
Choosing an input amplifier is easy if a few requirements
are taken into consideration. First, to limit the magnitude
of the voltage spike seen by the amplifier from charging
the sampling capacitor, choose an amplifier that has a low
output impedance (<100
) at the closed-loop bandwidth
frequency. For example, if an amplifier is used in a gain of
1 and has a unity-gain bandwidth of 50MHz, then the
output impedance at 50MHz must be less than 100
. The
second requirement is that the closed-loop bandwidth
must be greater than 40MHz to ensure adequate small-
signal settling for full throughput rate. If slower op amps
are used, more settling time can be provided by increasing
the time between conversions.
The best choice for an op amp to drive the LTC1414 will
depend on the application. Generally applications fall into
two categories: AC applications where dynamic specifica-
tions are most critical and time domain applications where
DC accuracy and settling time are most critical. The
following list is a summary of the op amps that are suitable
for driving the LTC1414. More detailed information is
available in the Linear Technology Databooks and on the
LinearView
TM CD-ROM.
LT
1223: 100MHz Video Current Feedback Amplifier.
6mA supply current.
±5V to ±15V supplies. Low noise.
Good for AC applications.
LT1227: 140MHz Video Current Feedback Amplifier. 10mA
supply current.
±5V to ±15V supplies. Low noise. Best for
AC applications.
LT1229/LT1230: Dual and Quad 100MHz Current Feed-
back Amplifiers.
±2V to ±15V supplies. Low noise. Good
AC specifications, 6mA supply current each amplifier.
LT1360: 50MHz Voltage Feedback Amplifier. 3.8mA sup-
ply current. Good AC and DC specs.
±5Vto±15Vsupplies.
70ns settling to 0.5LSB.
LT1363: 70MHz, 1000V/
s Op Amps. 6.3mA supply cur-
rent. Good AC and DC specifications. 60ns settling to
0.5LSB.
LT1364/LT1365: Dual and Quad 70MHz, 1000V/
s Op
Amps. 6.3mA supply current per amplifier. 60ns settling
to 0.5LSB.
LinearView is a trademark of Linear Technology Corporation.
AC Coupled Inputs
In applications where only the AC component of the analog
input is important, it may be desirable to AC couple the
input. This is easily accomplished by DC biasing the
LTC1414 analog input with a resistor to ground and using
a coupling capacitor to the input. Figure 7 shows a simple
AC coupled input circuit for the LTC1414 using only two
additional components. C1 is a 10
F ceramic capacitor
and R1 is a 1000
resistor to ground. R1 and C1 form a
highpass filter with a lower cut off frequency of 1/2
π(C1)R1
or 15.9Hz.
Differential Drive
In some applications the ADC drive circuitry is differential.
The differential drive can be applied directly to the LTC1414
without any special translation circuitry. Differential drive
can be advantageous at high frequencies (>1MHz) since it
provides improved THD and SFDR. Transformers can be
used to provide AC coupling, input scaling and single
ended to differential conversion as shown in Figure 8. The
resistor RS across the secondary will determine the input
impedance on the primary. The input impedance of the
primary RP will be related to the secondary load resistor RS
by the equation
RP = RS/n2
For example, if a Minicircuits T4-6T transformer is used,
the turns ratio is 2; if RS is 200 then RP is equal to 50.
The center tap of the secondary will set the common
mode voltage and should be grounded for optimal AC
performance.
LTC1414
AIN
+
ANALOG INPUT
AIN
–
VREF
REFCOMP
AGND
LTC1414 F07
1
2
3
4
5
R1
1k
C1
10
F
10
F
1
F
Figure 7. AC Coupled Input
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B6R-IV-S | CONVERTER MOD DC/DC 7.5V 150W |
| AD7899AR-3 | IC ADC 14BIT 400KSPS 5V 28-SOIC |
| VE-B6M-IV-S | CONVERTER MOD DC/DC 10V 150W |
| VI-23D-MX-F1 | CONVERTER MOD DC/DC 85V 75W |
| VE-B6H-IV-S | CONVERTER MOD DC/DC 52V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1414CGN#PBF | 功能描述:IC A/D CONV 14BIT SAMPLNG 28SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC1414CGN#PBF | 制造商:Linear Technology 功能描述:ADC, 14BIT, 2.2MSPS, SSOP-28 |
| LTC1414CGN#TR | 功能描述:IC ADC 14BIT 2.2MSPS SMPL 28SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC1414CGN#TRPBF | 功能描述:IC A/D CONV 14BIT SAMPLNG 28SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC1414IGN | 功能描述:IC A/D CONV 14BIT SAMPLNG 28SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。