- 您现在的位置：买卖IC网 > PDF目录20034 > LTC1421CG-2.5#PBF (Linear Technology)IC CONTROLLER HOT SWAP 24-SSOP PDF资料下载
参数资料
| 型号： | LTC1421CG-2.5#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/24页 |
| 文件大小： | 329K |
| 描述： | IC CONTROLLER HOT SWAP 24-SSOP |
| 标准包装： | 59 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 3 V ~ 12 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 管件 |
15
LTC1421/LTC1421-2.5
APPLICATIONS INFORMATION
U
U
U
time point 2). Pulses less than 20ms on POR are ignored.
CPON goes low. Both GATEHI and GATELO will be
actively pulled down to GND. When V
OUTLO
drops below
its reset threshold voltage, PWRGD will immediately pull
low (time point 3) followed by RESET and DISABLE 32祍
later (time point 4). Both supplies will be discharged to
ground and stay there until POR is pulled high.
The circuit breaker can be reset by pulling POR low. After
POR is low for more than 20ms, the chip will immediately
try to power up the supplies once the outputs are below the
V
TRIP
point.
Circuit Breaker Timing
The waveforms for the circuit when a short occurs on
either supply during board insertion are shown in
Figure 16. Time points 1 to 4 are the same as the board
insertion example, but at time point 5, a short circuit is
detected on one of the supplies. The charge pumps are
immediately turned off, the outputs V
OUTHI
and V
OUTLO
are
actively pulled to GND and the CPON and FAULT pins are
pulled low. At time point 6, the circuit breaker is reset by
pulling POR low. After POR has been low for 20ms (time
point 7), CPON and FAULT are pulled high, the 20礎
reference current is connected to RAMP and the charge
pumps are enabled. V
OUTHI
and V
OUTLO
ramp up at a
controlled rate. When V
OUTLO
has exceeded its reset
threshold, the PWRGD signal is pulled high (time point 8).
After a 200ms delay, RESET is pulled high and DISABLE
goes low.
Figure 16. Circuit Breaker Timing
V
CCLO
1
2
3
4
5
6
V
CCHI
DISABLE
CON1
7
8
9
CON2
CPON
PWRGD
V
TH1
1421 F16
V
OUTHI
GATEHI
GATELO
V
OUTLO
RESET
FAULT
POR
20ms
20ms
200ms
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J0L-CY-B1 | CONVERTER MOD DC/DC 28V 50W |
| T86C156M010EBSS | CAP TANT 15UF 10V 20% 2312 |
| VI-J32-CX-S | CONVERTER MOD DC/DC 15V 75W |
| 1N4007FF | DIODE STD REC 1A 1000V DO-41 |
| RMM31DTMD-S189 | CONN EDGECARD 62POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1421CGTR | 制造商:Linear Technology 功能描述: |
| LTC1421CSW | 制造商:Linear Technology 功能描述:Hot Swap Controller 2-CH 12V 24-Pin SOIC W |
| LTC1421CSW#PBF | 功能描述:IC CONTROLLER HOT SWAP 24-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC1421CSW#TR | 功能描述:IC CONTROLLER HOTSWAP ADJ 24SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC1421CSW#TRPBF | 功能描述:IC CONTROLLER HOT SWAP 24-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。