- 您现在的位置：买卖IC网 > PDF目录14805 > LTC1474CMS8-3.3#PBF (Linear Technology)IC REG BUCK 3.3V 0.75A 8MSOP PDF资料下载
参数资料
| 型号： | LTC1474CMS8-3.3#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 3.3V 0.75A 8MSOP |
| 标准包装： | 50 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 3 V ~ 18 V |
| PWM 型： | Burst Mode? |
| 电流 - 输出： | 750mA |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-MSOP |
| 产品目录页面： | 1333 (CN2011-ZH PDF) |
LTC1474/LTC1475
APPLICATIO N S I N FOR M ATIO N
LTC1475 Pushbutton On/Off and
Microprocessor Interface
The LTC1475 provides pushbutton control of power on/off
for use with handheld products. A momentary ground on
the ON pin sets an internal S/R latch to run mode while a
momentary ground on the LBI/OFF pin resets the latch to
shutdown mode. See Figure 6 for a comparsion of on/off
operation of the LTC1474 and LTC1475 and Figure 7 for a
comparison of the circuit implementations.
In the LTC1475, the LBI/OFF pin has a dual function as
both the shutdown control pin and the low battery com-
parator input. Since the “OFF” pushbutton is normally
open, it does not affect the normal operation of the low
battery comparator. In the unpressed state, the LBI/OFF
input is the divided down input voltage from the resistive
the depressed switch state is detected by the microcon-
troller through its input. The microcontroller then pulls the
LBI/OFF pin low with the connection to one of its ouputs.
With the LBI/OFF pin low, the LTC1475 powers down
turning the microcontroller off. Note that since the I/O pins
of most microcontrollers have a reversed bias diode
between input and supply, a blocking diode with less than
1 μ A leakage is necessary to prevent the powered down
microcontroller from pulling down on the ON pin.
Figure 19 in the Typical Applications section shows how to
use the low battery comparator to provide a low battery
lockout on the “ON” switch. The LBO output disconnects
the pushbutton from the ON pin when the comparator has
tripped, preventing the LTC1475 from attempting to start
up again until V IN is increased.
divider to the internal low battery comparator and will
normally be above or just below the trip threshold of
1.23V. When shutdown mode is desired, the LBI/OFF pin
RUN
100k
RUN
LTC1474
ON
100k
V IN
ON
LTC1475
is pulled below the 0.7V threshold to invoke shutdown.
LBI/OFF
LTC1474
RUN
OFF
MODE
RUN
SHUTDOWN
RUN
1474/75 F07
LTC1475
ON
LBI/OFF
ON OVERRIDES LBI/OFF
WHILE ON IS LOW
Figure 7. Simplified Implementation of
LTC1474 and LTC1475 On/Off
Absolute Maximum Ratings and Latchup Prevention
The absolute maximum ratings specify that SW (Pin 5) can
MODE
RUN
SHUTDOWN
RUN
1474/75 F06
never exceed V IN (Pin 7) by more than 0.3V. Normally this
situation should never occur. It could, however, if the
Figure 6. Comparison of LTC1474 and LTC1475
Run/Shutdown Operation
The ON pin has precedence over the LBI/OFF pin. As seen
in Figure 6, if both pins are grounded simultaneously, run
mode wins.
Figure 18 in the Typical Applications section shows an
example for the use of the LTC1475 to control on/off of a
microcontroller with a single pushbutton. With both the
microcontroller and LTC1475 off, depressing the
pushbutton grounds the LTC1475 ON pin and starts up the
LTC1475 regulator which then powers up the microcon-
troller. When the pushbutton is depressed a second time,
output is held up while the supply is pulled down. A
condition where this could potentially occur is when a
battery is supplying power to an LTC1474 or LTC1475
regulator and also to one or more loads in parallel with the
the regulator’s V IN . If the battery is disconnected while the
LTC1474 or LTC1475 regulator is supplying a light load
and one of the parallel circuits is a heavy load, the input
capacitor of the LTC1474 or LTC1475 regulator could be
pulled down faster than the output capacitor, causing the
absolute maximum ratings to be exceeded. The result is
often a latchup which can be destructive if V IN is reapplied.
Battery disconnect is possible as a result of mechanical
stress, bad battery contacts or use of a lithium-ion battery
11
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JVK-EY-F1 | CONVERTER MOD DC/DC 40V 50W |
| LT1956EFE#PBF | IC REG BUCK ADJ 1.5A 16TSSOP |
| LT1308BIS8#PBF | IC REG BOOST 5V 1A 8SOIC |
| LT1766EFE#PBF | IC REG BUCK ADJ 1.5A 16TSSOP |
| ABM08DTBI-S189 | CONN EDGECARD 16POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1474CMS8-5 | 功能描述:IC REG BUCK 5V 0.75A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1474CMS8-5#PBF | 功能描述:IC REG BUCK 5V 0.75A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1474CMS8-5#TR | 功能描述:IC REG BUCK 5V 0.75A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1474CMS8-5#TRPBF | 功能描述:IC REG BUCK 5V 0.75A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1474CMS8PBF | 制造商:Linear Technology 功能描述:DC-DC Converter Step-Down 3-18V MSOP8 |
发布紧急采购，3分钟左右您将得到回复。