- 您现在的位置：买卖IC网 > PDF目录13935 > LTC1474IS8-3.3 (Linear Technology)IC REG BUCK 3.3V 0.75A 8SOIC PDF资料下载
参数资料
| 型号： | LTC1474IS8-3.3 |
| 厂商： | Linear Technology |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 3.3V 0.75A 8SOIC |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 3 V ~ 18 V |
| PWM 型： | Burst Mode? |
| 电流 - 输出： | 750mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-SOIC |
LTC1474/LTC1475
APPLICATIO N S I N FOR M ATIO N
If the L MIN calculated is not practical, a larger I PEAK should
be used. Although the above equation provides the mini-
mum, better performance (efficiency, line/load regulation,
noise) is usually gained with higher values. At higher
inductances, peak current and frequency decrease (im-
proving efficiency) and inductor ripple current decreases
(improving noise and line/load regulation). For a given
inductor type, however, as inductance is increased, DC
resistance (DCR) increases, increasing copper losses,
and current rating decreases, both effects placing an
upper limit on the inductance. The recommended range of
inductances for small surface mount inductors as a func-
tion of peak current is shown in Figure 3. The values in this
range are a good compromise between the trade-offs
discussed above. If space is not a premium, inductors with
larger cores can be used, which extends the recom-
mended range of Figure 3 to larger values.
1000
500
100
section, increased inductance requires more turns of wire
and therefore copper losses will increase.
Ferrite and Kool M μ designs have very low core loss and
are preferred at high switching frequencies, so design
goals can concentrate on copper loss and preventing
saturation. Ferrite core material saturates “hard,” which
means that inductance collapses abruptly when the peak
design current is exceeded. This results in an abrupt
increase in inductor current above I PEAK and consequent
increase in voltage ripple. Do not allow the core to satu-
rate! Coiltronics, Coilcraft, Dale and Sumida make high
performance inductors in small surface mount packages
with low loss ferrite and Kool M μ cores and work well in
LTC1474/LTC1475 regulators.
Catch Diode Selection
The catch diode carries load current during the off-time.
The average diode current is therefore dependent on the
P-channel switch duty cycle. At high input voltages the
diode conducts most of the time. As V IN approaches V OUT
the diode conducts only a small fraction of the time. The
most stressful condition for the diode is when the output
is short-circuited. Under this condition, the diode must
safely handle I PEAK at close to 100% duty cycle.
To maximize both low and high current efficiency, a fast
switching diode with low forward drop and low reverse
leakage should be used. Low reverse leakage current is
50
10
100
1000
critical to maximize low current efficiency since the leak-
PEAK INDUCTOR CURRENT (mA)
1474/75 F03
Figure 3. Recommended Inductor Values
Inductor Core Selection
Once the value of L is known, the type of inductor must be
selected. High efficiency converters generally cannot
age can potentially approach the magnitude of the LTC1474/
LTC1475 supply current. Low forward drop is critical for
high current efficiency since loss is proportional to for-
ward drop. These are conflicting parameters (see Table 1),
but a good compromise is the MBR0530 0.5A Schottky
diode specified in the application circuits.
Table 1. Effect of Catch Diode on Performance
afford the core loss found in low cost powdered iron cores,
forcing the use of more expensive ferrite, molypermalloy
or Kool M μ ? cores. Actual core loss is independent of core
size for a fixed inductor value, but is very dependent on
inductance selected. As inductance increases, core losses
DIODE (D1)
BAS85
MBR0530
MBRS130
LEAKAGE
200nA
1 μ A
20 μ A
FORWARD NO LOAD
DROP SUPPLY CURRENT EFFICIENCY*
0.6V 9.7 μ A 77.9%
0.4V 10 μ A 83.3%
0.3V 16 μ A 84.6%
go down. Unfortunately, as discussed in the previous
*Figure 1 circuit with V IN = 15V, I OUT = 0.1A
Kool M μ is a registered trademark of Magnetics, Inc.
8
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6456UT17S+T | IC MPU SUPER 1.665V SOT23-6 |
| MAX6456UT22S+T | IC MPU SUPER 2.188V SOT23-6 |
| LT1076CR#TRPBF | IC REG MULTI CONFIG ADJ 2A D2PAK |
| LT1076CR#TR | IC REG MULTI CONFIG ADJ 2A D2PAK |
| 25TWL33MEFC6.3X7 | CAP ALUM 33UF 25V 20% LOW LEAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1474IS8-5 | 功能描述:IC REG BUCK 5V 0.75A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC1474IS8-5#PBF | 功能描述:IC REG BUCK 5V 0.75A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC1474IS8-5#TR | 功能描述:IC REG BUCK 5V 0.75A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC1474IS8-5#TRPBF | 功能描述:IC REG BUCK 5V 0.75A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC1474IS8-5PBF | 制造商:Linear Technology 功能描述:DC-DC Converter Step-Down 3-18V SOIC8 |
发布紧急采购，3分钟左右您将得到回复。