- 您现在的位置：买卖IC网 > PDF目录13951 > LTC1475CMS8#TRPBF (Linear Technology)IC REG BUCK ADJ 0.75A 8MSOP PDF资料下载
参数资料
| 型号： | LTC1475CMS8#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 0.75A 8MSOP |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调 |
| 输入电压： | 3 V ~ 18 V |
| PWM 型： | Burst Mode? |
| 电流 - 输出： | 750mA |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-MSOP |
LTC1474/LTC1475
APPLICATIO N S I N FOR M ATIO N
with a built-in internal disconnect. The user needs to
assess his/her application to determine whether this situ-
ation could occur. If so, additional protection is necessary.
Prevention against latchup can be accomplished by sim-
ply connecting a Schottky diode across the SW and V IN
pins as shown in Figure 8. The diode will normally be
reverse biased unless V IN is pulled below V OUT at which
time the diode will clamp the (V OUT – V IN ) potential to less
than the 0.6V required for latchup. Note that a low leakage
Schottky should be used to minimize the effect on no-load
supply current. Schottky diodes such as MBR0530, BAS85
and BAT84 work well. Another more serious effect of the
protection diode leakage is that at no load with nothing to
provide a sink for this leakage current, the output voltage
can potentially float above the maximum allowable toler-
ance. To prevent this from occuring, a resistor must be
connected between V OUT and ground with a value low
enough to sink the maximum possible leakage current.
LATCHUP
PROTECTION
SCHOTTKY
where P is the power dissipated by the regulator and θ JA
is the thermal resistance from the junction of the die to the
ambient temperature.
The junction temperature is given by:
T J = T A + T R
As an example consider the LTC1474/LTC1475 in dropout
at an input voltage of 3.5V, a load current of 300mA, and
an ambient temperature of 70 ° C. From the typical perfor-
mance graph of switch resistance, the on-resistance of the
P-channel switch at 70 ° C is 3.5 ? . Therefore, power dissi-
pated by the part is:
P = I 2 ? R DS(ON) = 0.315W
For the MSOP package, the θ JA is 150 ° C/W. Thus the
junction temperature of the regulator is:
T J = 70 ° C + (0.315)(150) = 117 ° C
which is near the maximum junction temperature of 125 o C.
Note that at higher supply voltages, the junction tempera-
ture is lower due to reduced switch resistance.
PC Board Layout Checklist
V IN SW
LTC1474
LTC1475
+
V OUT
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the LTC1474/LTC1475. These items are also illustrated
1474/75 F08
Figure 8. Preventing Absolute Maximum
Ratings from Being Exceeded
Thermal Considerations
In the majority of the applications, the LTC1474/LTC1475
do not dissipate much heat due to their high efficiency.
However, in applications where the switching regulator is
running at high ambient temperature with low supply
voltage and high duty cycles, such as dropout with the
switch on continuously, the user will need to do some
thermal analysis. The goal of the thermal analysis is to
determine whether the power dissipated by the regulator
exceeds the maximum junction temperature of the part.
The temperature rise is given by:
T R = P ? θ JA
12
graphically in the layout diagram of Figure 9. Check the
following in your layout:
1. Is the Schottky diode cathode closely connected to SW
(Pin 5)?
2. Is the 0.1 μ F input decoupling capacitor closely con-
nected between V IN (Pin 7) and ground (Pin 4)? This
capacitor carries the high frequency peak currents.
3. When using adjustable version, is the resistive divider
closely connected to the (+) and (–) plates of C OUT with
a 10pF capacitor connected across R2?
4. Is the 1000pF decoupling capacitor for the current
sense resistor connected as close as possible to Pins 6
and 7? If no current sense resistor is used, Pins 6 and
7 should be shorted.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1475CMS8#TR | IC REG BUCK ADJ 0.75A 8MSOP |
| LTC1475CMS8-5#TR | IC REG BUCK 5V 0.75A 8MSOP |
| LTC1434CGN | IC REG BUCK 3.3V/5V/ADJ 20SSOP |
| GCM31DTBN-S189 | CONN EDGECARD 62POS R/A .156 SLD |
| DS1834U | IC ECONORST DUAL LO OPN-DR 8USOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1475CS8 | 功能描述:IC REG BUCK ADJ 0.75A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1475CS8#PBF | 功能描述:IC REG BUCK ADJ 0.75A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1475CS8#TR | 功能描述:IC REG BUCK ADJ 0.75A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1475CS8#TRPBF | 功能描述:IC REG BUCK ADJ 0.75A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1475CS8-3.3 | 功能描述:IC REG BUCK 3.3V 0.75A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。