- 您现在的位置：买卖IC网 > PDF目录14075 > LTC1504AIS8#PBF (Linear Technology)IC REG BUCK SYNC ADJ 0.5A 8SOIC PDF资料下载
参数资料
| 型号： | LTC1504AIS8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 0.5A 8SOIC |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调 |
| 输入电压： | 4 V ~ 10 V |
| 频率 - 开关： | 200kHz |
| 电流 - 输出： | 500mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-SOIC |
LTC1504A
APPLICATIO N S I N FOR M ATIO N
phase margin. The typical applications in this data sheet
show compensation values that work with several combi-
nations of external components—use them as a starting
point. For complex cases or stubborn oscillations, contact
the LTC Applications Department.
External Schottky Diode
An external Schottky diode can be included across the
internal N-channel switch (Q2) to improve efficiency at
heavy loads. The diode carries the inductor current during
the nonoverlap time while the LTC1504A turns Q1 off and
Q2 on and prevents current from flowing in the intrinsic
body diode in parallel with Q2. This diode will improve
efficiency by a percentage point or two as output current
approaches 500mA and can help minimize erratic behav-
ior at very high peak current levels caused by excessive
parasitic current flow through Q2. A Motorola MBRS0530L
is usually adequate, with the cathode connected to SW and
the anode connected to GND. Note that this diode is not
required for normal operation and has a negligible effect
on efficiency at low (< 250mA) output currents.
V OUT
Soft Start and Current Limit
Soft start and current limit are linked in the LTC1504A. Soft
start works in a straightforward manner. An internal 12 μ A
current source connected to the SS pin will pull up an
external capacitor connected from SS to GND at a rate
determined by the capacitor value. COMP is clamped to a
voltage one diode drop above SS; as SS rises, COMP will
rise at the same rate. When COMP reaches roughly 2V
below V CC , the duty cycle will slowly begin to increase until
the output comes into regulation. As SS continues to rise,
the feedback amplifier takes over at COMP, the clamp
releases and SS rises to V CC .
Current limit operates by pulling down on the soft start pin
when it senses an overload condition at the output. The
current limit amplifier (I LIM ) compares the voltage drop
across the internal P-channel switch (Q1) during its on
time to the voltage at the I MAX pin. I MAX includes an internal
12 μ A pull-down, allowing the voltage to be set by a single
resistor between V CC and I MAX . When the IR drop across
Q1 exceeds the drop across the I MAX resistor, I LIM pulls
current out of the external soft start capacitor, reducing
the voltage at SS. A soft start capacitor should always be
used if current limit is enabled. SS, in turn, pulls down on
LTC1504A FB
COMP
R FB1 *
R FB2 *
COMP, limiting the output duty cycle and controlling the
output current. When the current overload is removed, the
I LIM amplifier lets go of SS and allows it to rise again as if
it were completing a soft start cycle. The size of the
C C
*ADJUSTABLE PARTS ONLY
1504A ? F04a
external soft start capacitor controls both how fast the
current limit responds once an overload is detected and
Figure 4a. Minimum Compensation Network
V OUT
how fast the output recovers once the overload is re-
moved. The soft start capacitor also compensates the
feedback loop created by the I LIM amplifier. Because the
I LIM loop is a current feedback loop, the additional phase
shift due to the output inductor and capacitor do not come
LTC1504A FB
R FB1 *
C FF *
into play and the loop can be adequately compensated
with a single capacitor. Usually a 0.1 μ F ceramic capacitor
COMP
R C
C C
C F
R FB2 *
from SS to GND provides adequate soft start behavior and
acceptable current limit response.
This type of current limit circuit works well with mild
current overloads and eliminates the need for an external
*ADJUSTABLE PARTS ONLY
1504A ? F04b
Figure 4b. Optimum Compensation Network
current sensing resistor, making it attractive for LTC1504A
applications. These same features also handicap the cur-
rent limit circuit under severe short circuits when the
9
相关PDF资料 |
PDF描述 |
|---|---|
| HM71-30101LFTR | HIGH PERF LOW COST INDUCTORS |
| MAX6869UK21D5S+T | IC MPU SUPERVISOR SOT23-5 |
| LTC1504AIS8 | IC REG BUCK SYNC ADJ 0.5A 8SOIC |
| MAX6869UK24D2S+T | IC MPU SUPERVISOR SOT23-5 |
| HM71-30680LFTR | HIGH PERF LOW COST INDUCTORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1504CS8 | 功能描述:IC REG BUCK SYNC ADJ 0.5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1504CS8#PBF | 功能描述:IC REG BUCK SYNC ADJ 0.5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC1504CS8#TR | 功能描述:IC REG BUCK SYNC ADJ 0.5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC1504CS8#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 0.5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC1504CS8-3.3 | 功能描述:IC REG BUCK SYNC 3.3V 0.5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。