- 您现在的位置：买卖IC网 > PDF目录10024 > LTC1535ISW (Linear Technology)IC TXRX ISO RS485 DIFF 28-SOIC PDF资料下载
参数资料
| 型号： | LTC1535ISW |
| 厂商： | Linear Technology |
| 文件页数： | 3/18页 |
| 文件大小： | 0K |
| 描述： | IC TXRX ISO RS485 DIFF 28-SOIC |
| 标准包装： | 27 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RS485 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC |
| 包装： | 管件 |
| 其它名称： | Q1084161 |
LTC1535
11
1535fb
APPLICATIONS INFORMATION
Driver Output and Slow Slew Rate Control
The LTC1535 uses a proprietary driver output stage that
allows a common mode voltage range that extends beyond
the power supplies. Thus, the high impedance state is
maintained over the full RS485 common mode range.
The output stage provides 100mA of short-circuit current
limiting in both the positive and negative directions. Thus,
even under short-circuit conditions, the supply voltage
from the open-loop DC converter will remain high enough
for proper communication across the isolation barrier. The
driver output will be disabled in the event of a thermal
shutdown and a fault condition will be indicated through
the RE weak output.
The CMOS level SLO pin selects slow or fast slew rates
on the RS485 driver output (see Figures 15, 16, 17, 18 for
typical waveforms). The SLO input has an internal 100k
pull-up resistor. When SLO is low, the driver outputs are
slew rate limited to reduce high frequency edges. Left open
or tied high, SLO defaults to fast edges. The part draws
more current during slow slew rate edges.
Monitoring Faults on RE
The RE pin can be used to monitor the following fault
conditions: low supply voltages, thermal shutdown or
a time-out fault when there is no data communication
across the barrier. During a fault, the receiver output,
RO, defaults to a high state (see Table 2). Open circuit or
short-circuit conditions on the twisted pair do not cause
a fault indication. However, the RS485 receiver defaults
to a high output state when the receiver input is open or
short-circuited.
The RE pin has a weak current drive output mode for
indicating fault conditions. This fault state can be polled
using a bidirectional microcontroller I/O line or by using
the circuit in Figure 11, where the control to RE is three-
stated and the fault condition read back from the RE pin.
The weak drive has 100μA pull-up current to indicate a
fault and 50μA pull-down current for no fault. This allows
the RE pin to be polled without disabling RE on nonfault
conditions.
Both sides contain a low voltage detect circuit. A
voltage less than 4.2V on the isolated side disables
communication.
RE
POLL
FAULT
FAULT INDICATED WHEN RE IS THREE-STATED
VCC
1535 F11
POLL
FAULT
BUFFER
RE
RO
DI
DE
GND
LTC1535
FAULT
VCC
Figure 11. Detecting Fault Conditions
相关PDF资料 |
PDF描述 |
|---|---|
| IDT7207L50P | IC FIFO 16384X18 50NS 28DIP |
| MS27472T10A98S | CONN RCPT 6POS WALL MT W/SCKT |
| LT1794ISW | IC OPAMP 200MHZ DUAL 20-SOIC |
| VI-26Y-MV-F4 | CONVERTER MOD DC/DC 3.3V 99W |
| IDT72V815L20PF | IC FIFO SYNC 512X18 20NS 128QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1535ISW#PBF | 功能描述:IC TRANSCEIVER RS485 ISO 28SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:RS-232 & USB Transceiver 标准包装:2,000 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SSOP（0.209"，5.30mm 宽） 供应商设备封装:16-SSOP 包装:带卷 (TR) 其它名称:296-19849-2 |
| LTC1535ISW#PBF | 制造商:Linear Technology 功能描述:RS485 Transceiver IC |
| LTC1535ISW#TR | 功能描述:IC TRANSCEIVER RS485 ISO 28SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC 包装:管件 |
| LTC1535ISW#TRPBF | 功能描述:IC TRANSCEIVER RS485 ISO 28SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC 包装:管件 |
| LTC1535ISWPBF | 制造商:Linear Technology 功能描述:Isolated RS485 Transceiver LTC1535 |
发布紧急采购，3分钟左右您将得到回复。