- 您现在的位置：买卖IC网 > PDF目录15362 > LTC1536CS8#TRPBF (Linear Technology)IC PREC TRPL SPPLY MONITOR 8SOIC PDF资料下载
参数资料
| 型号： | LTC1536CS8#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC PREC TRPL SPPLY MONITOR 8SOIC |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 3 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效/低有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 2.985V，4.725V，可调 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
LTC1536
APPLICATIO N S I N FOR M ATIO N
When the PBR is pulled low for less than t PB ( ≈ 2 sec), a
narrow (100 μ s typ) soft reset pulse is generated on the
SRST output pin after the button is released. The push-
button circuitry contains an internal debounce counter
which delays the output of the soft reset pulse by typically
20ms. This pin can be OR-tied to the RST pin and issue
what is called a “soft” reset. The SRST thereby resets the
microprocessor without interrupting the DRAM refresh
cycle. In this manner DRAM information remains undis-
turbed. Alternatively, SRST may be monitored by the
processor to initiate a software-controlled reset.
When the PBR pin is held low for longer than t PB ( ≈ 2 sec),
a standard reset is generated. Once the 2-second period
has elapsed, a reset signal is produced by the pushbutton
logic, thereby clearing the reset counter. Once the PBR
pin is released, the reset counter begins counting the
reset period (200ms nominal). Consequently, the reset
outputs remain asserted for approximately 200ms after
the button is released.
Fast Undervoltage for PCI Applications
The LTC1536 is designed for PCI Local Bus applications
that require reset to be asserted quickly in response to one
or both of the power supply rails (5V and 3.3V) going out
of spec. The spec for t FAIL and t PF are met with enough
margin to give the designer the ability to add follow-on
logic as needed by system requirements. The V CCA pin can
be used to monitor the “power good” signal and keep reset
applied until both supplies are in spec and the power good
signal is high.
TYPICAL APPLICATIO N S N
PCI Expansion Board RST Generation
3.3V SUPPLY
Glitch Immunity and Fast Undervoltage Detection
The LTC1536 achieves its high speed characteristics while
maintaining glitch immunity by using two sets of com-
parators. The V CC5 and V CC3 sense inputs each have two
comparators set at different thresholds. A slow, very
accurate comparator monitors the supply for precision
undervoltage detection. In parallel, but with a threshold
250mV lower than the precision threshold, is a very fast
comparator that detects when the supply is quickly going
out of specification. Because the fast comparator thresh-
old is set 250mV above the PCI specification, typical
values for t FAIL can be negative.
3V or 5V Power Detect/Gate Drive
The LTC1536 for the most part is powered internally from
the V CC3 pin. The exception is at the gate drive of the output
FET on the RST pin. On the gate to this FET is power detect
circuitry used to detect and drive the gate from either the
3.3V pin or the 5V pin, whichever pin has the highest
potential. This ensures the part pulls the RST pin low as
soon as either input pin is ≥ 1V.
Extended ESD Tolerance of the PBR Input Pin
The PBR pin is susceptible to ESD since it can be brought
out to a front panel in normal applications. The ESD
tolerance of this pin can be increased by adding a resistor
in series with the PBR pin. A 10k resistor can increase the
ESD tolerance of the PBR pin to approximately 10kV. The
PBR’s internal pull-up current of 7 μ A typical means there
is only 70mV (150mV max) dropped across the resistor.
Dual Supply Monitor (3.3V and 5V, V CCA Input
Monitoring “Power Good”)
PCI
LOCAL
BUS
5V SUPPLY
0.1 μ F
0.1 μ F
1
2
3
4
LTC1536
V CC3 PBR
V CC5 SRST
V CCA RST
GND RST
8
7
6
5
ONBOARD
DEVICE
3.3V
5V
PWR GOOD
1
2
3
4
LTC1536
V CC3 PBR
V CC5 SRST
V CCA RST
GND RST
8
7
6
5
SYSTEM RESET
RESET
1536 TA08
1536 TA04
1536fa
8
相关PDF资料 |
PDF描述 |
|---|---|
| IDC7328ER221M | INDUCTOR POWER 220UH 1.2A SMD |
| LTC1536CS8#TR | IC MONITOR PREC TRPL SPPLY 8SOIC |
| 160-474JS | INDUCTOR RF CHIP 470UH 5% SMD |
| IDC7328ER220M | INDUCTOR POWER 22UH 3.5A SMD |
| 160-394JS | INDUCTOR RF CHIP 390UH 5% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1536IS8 | 功能描述:IC PREC TRPL SPPLY MONITOR 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC1536IS8#PBF | 功能描述:IC PREC TRPL SPPLY MONITOR 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC1536IS8#TR | 功能描述:IC MONITOR PREC TRPL SPPLY 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC1536IS8#TRPBF | 功能描述:IC PREC TRPL SPPLY MONITOR 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC1538CG-AUX | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
发布紧急采购，3分钟左右您将得到回复。