- 您现在的位置：买卖IC网 > PDF目录17162 > LTC1558CS-5#TRPBF (Linear Technology)IC BACKUP BATT CNTRLR 5V 16-SOIC PDF资料下载
参数资料
| 型号： | LTC1558CS-5#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/20页 |
| 文件大小： | 0K |
| 描述： | IC BACKUP BATT CNTRLR 5V 16-SOIC |
| 标准包装： | 2,500 |
| 功能： | 备份管理 |
| 电池化学： | 镍镉 |
| 电源电压： | 4.4 V ~ 5.25 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
LTC1558-3.3/LTC1558-5
APPLICATIO N S I N FOR M ATIO N
terminate backup operation and remain off until the main
power supply returns. It then runs a fast recharge cycle to
recharge the backup cell. An onboard low-battery com-
parator in the 16-pin GN or SO package provides an early
warning signal when the backup cell drops below 1V.
The UVLO circuit also trips if the LTC1558’s V CC supervi-
sory circuit detects that V CC drops below – 9% of the rated
V CC voltage due to overload or output short-circuit condi-
tions. Once the UVLO circuit trips, the LTC1558 asserts
the RESET pins until the V CC voltage drops below 1V. It will
then remain off until V CC rises to within (V CC – 6%) of the
rated output voltage. During power-up from UVLO, the
LTC1558 asserts the RESET pins until the (V CC – 6%)
threshold. Once V CC exceeds (V CC – 6%), the RESET pins
remain asserted for another 200ms (“hard” reset) before
being released to inform the system to start operating.
Reset Operation
The LTC1558 includes an onboard pushbutton reset switch
controller. If the CTL pin is pulled to ground (< 250mV) by
a pushbutton or an open-drain output, the LTC1558 gen-
erates a pulse at the RESETpins after the trailing edge of
the CTL signal. A short (less than 2s) low going signal at
CTL will generate a “soft” reset (100 μ s) pulse at the RESET
pins. A low CTL signal for more than 2s will generate a
“hard” reset pulse at its RESETpins. During “hard” reset,
the LTC1558 will disable the boost converter if it is in
backup mode. All signals at the CTL pin are debounced for
20ms to prevent multiple resets, allowing the CTL pin to be
connected directly to a pushbutton to ground.
The RESET pin is an open-drain output that requires an
external pull-up resistor. The RESET pin is a TTL-compat-
ible CMOS output.
Shutdown
The 16-pin LTC1558 has a TTL-compatible input, SHDN,
that shuts down the whole chip, asserts the RESET pins
and places the CTL, V BAK and SW pins into high impedance
states. The SHDN pin has an internal pull-up that ensures
the chip will not shut down if the pin is left floating. The
SHDN pin typically draws 8 μ A when pulled low at V CC = 5V.
The chip consumes less than 50 μ A during shutdown while
V CC is still alive.
Although there is no SHDN pin for the SO-8 package, the
CTL
A
0V
B
> 0.25V
20ms < t CTL < 2s
user can shut down the part by pulling CTL to ground. The
chip enters “hard” reset leaving only the bandgap and
t CTL < 20ms
comparators alive. The charger and the boost converter
RESET
20ms
100 μ s
100 μ s
shut off completely. Note that the backup cell slowly
discharges through R EXT in this mode.
DEBOUNCE
“SOFT” PUSHBUTTON RESET AT CTL
A. CTL < 0.25V FOR LESS THAN 20ms
Inductor Selection
CTL
RESET
CTL
B. CTL > 0.25V FOR MORE THAN 20ms
0V
t CTL > 2s
2s
“HARD” PUSHBUTTON RESET AT CTL
CTL < 0.25V FOR MORE THAN 2s
0V
20ms
200ms
> 0.25V
The LTC1558 is designed to operate with a recommended
inductor value of 22 μ H ( ± 20%) with < 0.2 ? DC resistance.
Using inductor values higher than 22 μ H will deliver more
output power but will cause the gas gauge counter to
count inaccurately and under recharge the backup cell. At
the same time, the N-channel transistor timer will limit the
peak current if the charging time becomes overextended
due to the higher inductor value. Using inductor values
lower than 22 μ H will degrade the boost converter’s maxi-
mum output power and cause the gas gauge counter to
RESET
20ms
20ms DEBOUNCE AT FALLING AND RISING RESET EDGE
1558 F05
overcharge the backup cell. Table 2 lists the recom-
mended surface mount inductor part numbers.
Figure 5. Pushbutton Resets
13
相关PDF资料 |
PDF描述 |
|---|---|
| DK-57TS-LPC3250 | KIT LCD TOUCH 5.7" FOR LPC3250 |
| 594D107X9016C2W | CAP TANT 100UF 16V 10% 2812 |
| C8051F020DK | DEV KIT FOR F020/F021/F022/F023 |
| 0210490737 | CABLE JUMPER 1.25MM .229M 5POS |
| 0210490736 | CABLE JUMPER 1.25MM .203M 5POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1558CS8-3.3 | 功能描述:IC BACKUP BATT CNTRLR 3.3V 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:2,000 系列:Impedance Track™ 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.4 V ~ 2.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:带卷 (TR) 产品目录页面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名称:296-21665-2 |
| LTC1558CS8-3.3#PBF | 功能描述:IC BACKUP BATT CNTRLR 3.3V 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LTC1558CS8-3.3#TRPBF | 功能描述:IC BACKUP BATT CNTRLR 3.3V 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LTC1558CS8-5 | 功能描述:IC BACKUP BATT CONTRLR 5V 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1558CS8-5#PBF | 功能描述:IC BACKUP BATT CONTRLR 5V 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
发布紧急采购，3分钟左右您将得到回复。