- 您现在的位置：买卖IC网 > PDF目录16225 > LTC1559CGN-5 (Linear Technology)IC BACKUP BATT CNTRLR 5V 16-SSOP PDF资料下载
参数资料
| 型号： | LTC1559CGN-5 |
| 厂商： | Linear Technology |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC BACKUP BATT CNTRLR 5V 16-SSOP |
| 标准包装： | 100 |
| 功能： | 备份管理 |
| 电池化学： | 镍镉 |
| 电源电压： | 4.4 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 1340 (CN2011-ZH PDF) |
LTC1559-3.3/LTC1559-5
APPLICATIO N S I N FOR M ATIO N
If V CC is still less than V CC (rated value) – 7% (LTC1559-
3.3) after the first boost cycle, the LTC1559 immediately
reconnects SW to ground, repeating the boost cycle. If
after two consecutive pulses, V CC is still not above the
boost threshold V CC (rated value) – 7% (LTC1559-3.3),
the LTC1559 decides that the load is not so light after all,
and doubles the internal inductor charging current limit to
330mA for subsequent cycles. This is high current mode.
By doubling the peak inductor current, each boost cycle
effectively carries four times more energy compared to
low current mode (E = 1/2 ? LI 2 ), doubling the available
output power. When V CC exceeds the V CC (rated value)
– 7% (LTC1559-3.3) boost threshold, the LTC1559 stops
the boost converter and resets the internal 2-pulse counter.
The next time V CC falls below V CC (rated value) – 7%
(LTC1559-3.3), the boost converter restarts in low current
mode for at least two boost cycles. Moderate or changing
loads cause the LTC1559 to shift between the two peak
inductor current limits, keeping the output in tight regula-
tion. Near its maximum load capability, the LTC1559 will
stay in 330mA high current mode and the output voltage
V BAK will hover around V CC (rated value) – 7%
(LTC1559-3.3).
V CC Capacitor ESR
The type of output capacitor and the rated V CC value will
affect the LTC1559’s output ripple and efficiency. In most
applications, the V CC capacitor is primarily determined by
the requirements of the main power supply. Such a
capacitor will generally meet the requirements of the
LTC1559. In unusual circumstances or circuits where
the main system V CC capacitor is located some distance
away from the LTC1559, a local output capacitor may be
necessary.
The ripple on the V CC pin is equal to the capacitor ESR
voltage drop due to the boost converter’s output current
pulses. The ripple frequency and output duty cycle is
proportional to the inductor discharge time. Given a fixed
inductor value (22 μ H) and a known peak current limit, the
booster’s discharge time in each boost cycle is propor-
tional to the difference between V BAK (93% of the rated V CC
for the LTC1559-3.3 and 92.5% of the rated V CC for the
LTC1559-5) and the battery cell voltage, V BAT (1.2V).
10
Assuming ESR = 0.2 ? , I IND(PEAK) = 330mA, V CC = 5V,
V RIPPLE(P-P) = (I IND(PEAK) )(R ESR(CAP) )
= (330mA)(0.2 ? )
= 66mV
Since V CC must be scaled down internally, the external
resistor ratio:
= 5V/1.272V
= 3.931
Therefore the ripple seen by the V CC comparators is:
= 66mV/3.931
= 16.79mV
The discharge time period,
t DISCH = (L ? I IND(PEAK) )/(V BAK – V BAT )
= (22 μ H ? 330mA)/(4.625 – 1.2V)
= 2.12 μ s
For V CC = 3.3V and I IND(PEAK) = 330mA,
V RIPPLE(P-P) = 66mV
RB resistor ratio = 3.3/1.272 = 2.594
Ripple voltage = 25.4mV
t DISCH = 3.9 μ s
The internal V CC comparators are designed to have a slow
response time to filter away this ripple. The V CC (rated
value) – 5.5% (LTC1559-3.3) and V CC (rated value) – 9%
comparators have a 6 μ s rising edge delay and 2 μ s falling
edge delay. The V CC (rated value) – 7% (LTC1559-3.3)
comparator has a similar 6 μ s rising time delay but a much
longer falling time delay of 20 μ s. This enables the com-
parator to control the boost converter properly, and avoids
turning off the boost converter prematurely due to false
triggering by the ESR ripple.
Exit from Backup
When a main battery is inserted into the system, the
LTC1559 follows a specific sequence to exit backup mode
and return control to the main supply. The sequence
depends on the type of main power supply used. In
systems where the main supply’s output impedance is
相关PDF资料 |
PDF描述 |
|---|---|
| UVZ2C471MRD | CAP ALUM 470UF 160V 20% RADIAL |
| GEC43DREN-S13 | CONN EDGECARD 86POS .100 EXTEND |
| UPZW6820MHD | CAP ALUM 82UF 420V 20% RADIAL |
| GCC18DREI-S13 | CONN EDGECARD 36POS .100 EXTEND |
| SLPX331M250A3P3 | CAP ALUM 330UF 250V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1559CGN-5#PBF | 功能描述:IC BACKUP BATT CNTRLR 5V 16-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LTC1559CGN-5#TRPBF | 功能描述:IC BACKUP BATT CNTRLR 5V 16-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LTC1559CS-3.3 | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1559CS-3.3#PBF | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LTC1559CS-3.3#TRPBF | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
发布紧急采购，3分钟左右您将得到回复。