- 您现在的位置：买卖IC网 > PDF目录16015 > LTC1559CS8-3.3 (Linear Technology)IC BACKUP BATT CNTRLR 3.3V 8SOIC PDF资料下载
参数资料
| 型号： | LTC1559CS8-3.3 |
| 厂商： | Linear Technology |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | IC BACKUP BATT CNTRLR 3.3V 8SOIC |
| 标准包装： | 100 |
| 功能： | 备份管理 |
| 电池化学： | 镍镉 |
| 电源电压： | 2.9 V ~ 3.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
LTC1559-3.3/LTC1559-5
APPLICATIO N S I N FOR M ATIO N
Overview
Table 1. LTC1559-3.3 Operating Modes
The LTC1559 is a versatile backup battery control system
designed to provide all the functions necessary to imple-
ment a complete, highly integrated backup system within
a single chip. It allows the system to maintain its rated
supply voltage during backup, offering maximum sys-
tem design flexibility. The LTC1559 allows the use of a
low cost rechargeable NiCd cell for backup, eliminating
the need for expensive, replaceable 4.5V lithium backup
cells.
The LTC1559 includes an onboard boost converter
OPERATING MODES
UVLO Reset
Push-Button Reset
UVLO Reset Recovery
Backup Mode Activation
Backup Mode Exit
Boost Converter Activation
Boost Converter Deactivation
CONDITIONS
1V < V CC < V CC (rated value) – 9% or
V BAT < 0.9V
V CTL < 250mV
V CC > V CC (rated value) – 5.5%
V CC < V CC (rated value) – 7%
V CC > V CC (rated value) – 5.5%
or PS > V CC
V CC < V CC (rated value) – 7%
V CC > V CC (rated value) – 7%
designed to generate a fixed voltage (3.07V for 3.3V parts
Table 2. LTC1559-5 Operating Modes
and 4.625V for 5V parts) from a single 1.2V NiCd cell.
When connected to the system DC/DC converter’s output,
the LTC1559 enables the system connected to the V CC rail
to continue operation when the main power supply fails. A
“smart” recharging circuit uses an accumulating gas
gauge to measure the charge extracted from the backup
battery during a backup cycle. This measured charge is
then replaced in a fast recharge cycle, without wasting
excess power or overcharging the backup cell. An exter-
nally adjustable trickle charge circuit maintains the cell
charge after the fast charge cycle has completed, minimiz-
OPERATING MODES
UVLO Reset
Push-Button Reset
UVLO Reset Recovery
Backup Mode Activation
Backup Mode Exit
Boost Converter Activation
Boost Converter Deactivation
CONDITIONS
1V < V CC < V CC (rated value) – 9%
or V BAT < 0.9V
V CTL < 250mV
V CC > V CC (rated value) – 6%
V CC < V CC (rated value) – 7.5%
V CC > V CC (rated value) – 6%
or PS > V CC
V CC < V CC (rated value) – 7.5%
V CC > V CC (rated value) – 7.5%
ing drain from the main battery during standby.
Included in the LTC1559 is a complete backup circuit that
monitors the main system power and automatically
switches in the backup circuit as the primary power supply
falls away (due to a weak or disconnected main battery).
The LTC1559 also performs V CC supervisory functions
during normal system operations. An LTC1559-3.3
monitors a 3.3V supply voltage at its V CC pin while an
LTC1559-5 monitors a 5V supply at its V CC pin. In both
cases, the LTC1559 derives power for the majority of the
internal circuitry (except for the boost converter) from its
V CC pin. Table 1 shows the signal conditions for the
various operating modes of the LTC1559-3.3. Table 2
shows the signal conditions for the various operating
modes of the LTC1559-5.
Boost Converter Operation
The LTC1559 uses an onboard boost converter with a
fixed peak current architecture that provides a simple and
flexible system solution while eliminating the need for
conventional frequency compensation. The boost
converter’s output, set to 93% (LTC1559-3.3) or 92.5%
(LTC1559-5) of the rated V CC , supports the system V CC
during backup. It supplies a minimum backup power of
100mW. The boost converter operates in a modified
pulse-skipping mode; each switch cycle transfers a known
amount of charge from the backup cell to the regulated
output. This prevents uncontrolled discharge of the backup
cell and allows the LTC1559 to accurately measure the
charge removed from the backup cell by counting the
charge pulses.
The LTC1559 enters backup mode when the main battery
voltage drops and causes V CC , the system regulator’s
output, to fall. As shown in Figure 1, V CC is scaled down
by an internal resistor divider and fed to the LTC1559’s
backup comparators. These compare the scaled voltage
8
相关PDF资料 |
PDF描述 |
|---|---|
| M3CFK-5006J | IDC CABLE - MKC50K/MC50G/MCF50K |
| HCM18DRXH | CONN EDGECARD 36POS DIP .156 SLD |
| M3CGK-5006J | IDC CABLE - MKC50K/MC50G/MCS50K |
| LTC1558CS8-5 | IC BACKUP BATT CONTRLR 5V 8-SOIC |
| MAX810MEXR+T | IC RESET CIRC MPU SC70-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1559CS8-5 | 功能描述:IC BACKUP BATT CNTRLR 5V 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:2,000 系列:Impedance Track™ 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.4 V ~ 2.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:带卷 (TR) 产品目录页面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名称:296-21665-2 |
| LTC1559CS8-5#PBF | 功能描述:IC BACKUP BATT CNTRLR 5V 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:2,000 系列:Impedance Track™ 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.4 V ~ 2.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:带卷 (TR) 产品目录页面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名称:296-21665-2 |
| LTC1559CS8-5#TRPBF | 功能描述:IC BACKUP BATT CNTRLR 5V 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LTC1560-1CS8 | 功能描述:IC FILTER ELLIPTIC LOWPASS 8SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| LTC1560-1CS8#PBF | 功能描述:IC FILTER ELLIPTIC LOWPASS 8SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。