- 您现在的位置：买卖IC网 > PDF目录11026 > LTC1566-1IS8#TR (Linear Technology)IC FILTER LP 7ORDER 2.3MHZ 8SOIC PDF资料下载
参数资料
| 型号： | LTC1566-1IS8#TR |
| 厂商： | Linear Technology |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | IC FILTER LP 7ORDER 2.3MHZ 8SOIC |
| 标准包装： | 2,500 |
| 滤波器类型： | 低通 |
| 频率 - 截止或中心： | 150kHz |
| 滤波器数： | 1 |
| 滤波器阶数： | 7th |
| 电源电压： | ±5V，5V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
LTC1566-1
6
15661fa
a common mode voltage that is equal to one-half of the total
supply voltage. Figure 5 illustrates the THD versus output
common mode voltage for a 0.5VP-P/2.0VP-P differential
input/output voltage and a common mode input voltage
that is equal to one-half the total supply voltage.
Output DC Offset Control
A unique feature of the LTC1566-1 is the ability to introduce
a differential offset voltage at the output of the filter. As
seen in the “Block Diagram”, if a DC voltage is applied to Pin
5 with respect to Pin 3, the same voltage will be added to
the differential voltage seen between Pins 8 and 7.
The output DC offset control pin can be used for sideband
suppression in differential modulators, calibration of A/D
converters, or simple signal summation. Since the voltage
summing occurs at the output of the filter, Pin 5 acts as a
unfiltered input. The response from Pin 5 to Pin 8 – Pin 7
with Pins 1,2 and 3 grounded is shown in Figure 7. The
range of voltages that can be applied to Pin 5 is shown in
Figure 6 where THD is plotted versus output offset. Pin 3 is
biased to mid supply.
Output Drive
Pins 7 and 8 can drive a 1k or 300pF load connected to
AC ground with a ±0.5V signal (corresponding to a 2VP-P
differential signal). For differential loads (loads connected
across Pins 7 and 8) the outputs can produce a 2VP-P
differential signal across 2k or 150pF. For smaller signal
amplitudes the outputs can drive correspondingly larger
loads.
–5 –4
–2
0
2
4
–30
–40
–50
–60
–70
–80
–90
–3
–1
1
3
1566-1 F03
5
INPUT COMMON MODE VOLTAGE (V)
THD
(dB)
VS = 5V
VS = ±5V
DIFFERENTIAL OUTPUT (VP-P)
0.5
THD,
SNR
(dB)
–30
–40
–50
–60
–70
–80
–90
2.0
3.0
1566-1 F04
1.0
1.5
2.5
3.5
4.0
VS = 5V
VS = ±5V
S/N
OUTPUT COMMON MODE VOLTAGE (V)
–4
THD
(dB)
–30
–40
–50
–60
–70
–80
–90
–1
2
1566-1 F05
–3
–2
1
03
4
VS = 5V
VS = ±5V
Figure 3
Figure 4
Figure 5
APPLICATIO S I FOR ATIO
WU
U
Input Common Mode and Differential Voltage Range
The range of voltage each input can support while operat-
ing in its linear region is typically 0.8V to 3.7V for a single
5V supply and – 4.2V to 3.2V for a ±5V supply. Therefore,
the filter can accept a variety of common mode input
voltages. Figure 3 shows the total harmonic distortion of
the filter versus input common mode voltage with a
2VP-P differential output signal.
Figure 4 shows the total harmonic distortion and signal to
noise ratio versus differential output voltage level for both
a single 5V and a ±5V supply. The common mode voltage
of the input signal is one-half the total power supply voltage
of the filter. The spurious free dynamic range (SFDR), the
level where the THD and S/N ratio are equal, is 72dB.
For best performance, the inputs should be driven differen-
tially. For single-ended signals, connect the unused input
to Pin 3 or a common mode reference.
The filter DC differential swings listed in the “Electrical
Characteristics” are measured with input differential volt-
ages of 0.9VP-P and 1.5VP-P for 5V and ±5V supplies
respectively. Ideally the corresponding output levels would
be 3.6VP-P and 6VP-P. As seen in Figure 4, these levels are
above the range of linear operation. Input signals larger
than 0.9VP-P/1.5VP-P will result in phase inversion and
should be avoided.
Output Common Mode and Differential Voltage Range
The output is a fully differential signal with a common
mode level equal to the voltage at Pin 3 when Pin 5 is
shorted to Pin 3. The best performance is achieved using
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B0D-IY-F1 | CONVERTER MOD DC/DC 85V 50W |
| LTC1068-200CG#TRPBF | IC FILTR BUILDNG BLK QUAD 28SSOP |
| VE-B0B-IY-F3 | CONVERTER MOD DC/DC 95V 50W |
| LTC1068-200CG#TR | IC FILTER BUILDG BLK QUAD 28SSOP |
| LTC1068CG#TRPBF | IC FILTR BUILDNG BLK QUAD 28SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1569CS8-6 | 功能描述:IC FILTER 10TH ORDR LOWPASS8SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| LTC1569CS8-6#PBF | 功能描述:IC FILTER 10TH ORDR LOWPASS8SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| LTC1569CS8-6#PBF | 制造商:Linear Technology 功能描述:IC FILTER LOW PASS 64KHZ 8-SOIC 制造商:Linear Technology 功能描述:IC, FILTER, LOW PASS, 64KHZ, 8-SOIC |
| LTC1569CS8-6#TR | 功能描述:IC FILTER LP 10TH ORD LIN 8SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| LTC1569CS8-6#TRPBF | 功能描述:IC FILTER 10TH ORDR LOWPASS8SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。