- 您现在的位置：买卖IC网 > PDF目录4962 > LTC1622CS8#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 8-SOIC PDF资料下载
参数资料
| 型号： | LTC1622CS8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 8-SOIC |
| 标准包装： | 100 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 625kHz |
| 占空比： | 100% |
| 电源电压： | 2 V ~ 10 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1333 (CN2011-ZH PDF) |
LTC1622
APPLICATIO N S I N FOR M ATIO N
I RIPPLE = IN OUT ? OUT D ?
() ? V IN + V D ?
The basic LTC1622 application circuit is shown in Figure
1. External component selection is driven by the load
requirement and begins with the selection of L and R SENSE .
Next, the Power MOSFET and the output diode D1 are
selected followed by C IN and C OUT .
R SENSE Selection for Output Current
R SENSE is chosen based on the required output current.
With the current comparator monitoring the voltage devel-
oped across R SENSE , the threshold of the comparator
determines the inductor’s peak current. The output cur-
rent the LTC1622 can provide is given by:
V OUT . The inductor’s peak-to-peak ripple current is given
by:
V ? V ? V + V ?
fL
where f is the operating frequency. Accepting larger values
of I RIPPLE allows the use of low inductances, but results in
higher output voltage ripple and greater core losses. A
reasonable starting point for setting ripple current is
I RIPPLE = 0.4(I OUT(MAX) ). Remember, the maximum I RIPPLE
occurs at the maximum input voltage.
With Burst Mode operation selected on the LTC1622, the
? RIPPLE
I OUT =
0 . 08
R SENSE
I
2
ripple current is normally set such that the inductor
current is continuous during the burst periods. Therefore,
the peak-to-peak ripple current should not exceed:
where I RIPPLE is the inductor peak-to-peak ripple current
(see Inductor Value Calculation section).
A reasonable starting point for setting ripple current is
I RIPPLE ≤
0 . 036
R SENSE
I RIPPLE = (0.4)(I OUT ). Rearranging the above equation, it
becomes:
This implies a minimum inductance of:
( )( )
L MIN = IN OUT ? OUT D ?
f ? ?
R SENSE =
1
15 I OUT
for Duty Cycle < 40%
V ? V ? V + V ?
? 0 . 036 ? ? V IN + V D ?
? R SENSE ?
However, for operation that is above 40% duty cycle, slope
compensation has to be taken into consideration to select
the appropriate value to provide the required amount of
current. Using Figure 2, the value of R SENSE is:
(Use V IN(MAX) = V IN )
A smaller value than L MIN could be used in the circuit;
however, the inductor current will not be continuous
during burst periods.
( )( I OUT )( )
R SENSE =
15 100
SF
Inductor Core Selection
Once the value for L is known, the type of inductor must be
Inductor Value Calculation
The operating frequency and inductor selection are inter-
related in that higher operating frequencies permit the use
of a smaller inductor for the same amount of inductor
ripple current. However, this is at the expense of efficiency
due to an increase in MOSFET gate charge losses.
The inductance value also has a direct effect on ripple
current. The ripple current, I RIPPLE , decreases with higher
inductance or frequency and increases with higher V IN or
selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron cores,
forcing the use of more expensive ferrite, molypermalloy
or Kool Mu ? cores. Actual core loss is independent of core
size for a fixed inductor value, but it is very dependent on
inductance selected. As inductance increases, core losses
go down. Unfortunately, increased inductance requires
more turns of wire and therefore copper losses will
increase. Ferrite designs have very low core losses and are
Kool Mu is a registered trademark of Magnetics, Inc.
7
相关PDF资料 |
PDF描述 |
|---|---|
| ABB24DHNT | CONN EDGECARD 48POS .050 DIP SLD |
| ABC15DRXH-S734 | CONN EDGECARD 30POS DIP .100 SLD |
| UCA2E220MHD1TO | CAP ALUM 22UF 250V 20% RADIAL |
| ABC17DRTN-S734 | CONN EDGECARD 34POS DIP .100 SLD |
| UCD0J681MNL1GS | CAP ALUM 680UF 6.3V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1622IS8 | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1622IS8#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
| LTC1622IS8#TR | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1622IS8#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1623CMS8 | 功能描述:IC HI-SIDE SW CNTRLR DUAL 8-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:5 系列:- 配置:低端 输入类型:非反相 延迟时间:600ns 电流 - 峰:12A 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:- 电源电压:14.2 V ~ 15.8 V 工作温度:-20°C ~ 60°C 安装类型:通孔 封装/外壳:21-SIP 模块 供应商设备封装:模块 包装:散装 配用:BG2A-NF-ND - KIT DEV BOARD FOR IGBT 其它名称:835-1063 |
发布紧急采购，3分钟左右您将得到回复。