- 您现在的位置：买卖IC网 > PDF目录15283 > LTC1624IS8 (Linear Technology)IC REG CTRLR BST FLYBK INV 8SOIC PDF资料下载
参数资料
| 型号： | LTC1624IS8 |
| 厂商： | Linear Technology |
| 文件页数： | 8/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST FLYBK INV 8SOIC |
| 标准包装： | 100 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 225kHz |
| 占空比： | 95% |
| 电源电压： | 3.5 V ~ 36 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 是 |
| 反相： | 是 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC1624
APPLICATIO N S I N FOR M ATIO N
? V
( )
( )
I DIODE AVG LOAD AVG ? V IN OUT ?
= I
V + V D
( ) ( ) ( )
P MAIN = OUT D I MAX
1 + δ R DS ON +
k ( V IN ) ( I MAX )( C RSS )( )
P D ? V IN + V D ?
V IN ? ?
( )
[ V ( V ) ]
Step-Down Converter: Power MOSFET Selection
One external N-channel power MOSFET must be selected
for use with the LTC1624 for the top (main) switch.
The peak-to-peak gate drive levels are set by the INTV CC
voltage. This voltage is typically 5V. Consequently, logic
level threshold MOSFETs must be used in most LTC1624
applications. If low input voltage operation is expected
(V IN < 5V) sublogic level threshold MOSFETs should be
used. Pay close attention to the BV DSS specification for the
MOSFETs as well; many of the logic level MOSFETs are
limited to 30V or less.
Selection criteria for the power MOSFET include the “ON”
resistance R DS(ON) , reverse transfer capacitance C RSS ,
input voltage and maximum output current. When the
LTC1624 is operating in continuous mode the duty cycle
for the top MOSFET is given by:
Main Switch Duty Cycle = OUT
V IN + V D
The MOSFET power dissipation at maximum output
current is given by:
V + V 2
V IN + V D
1 . 85
f
where δ is the temperature dependency of R DS(ON) and k
is a constant inversely related to the gate drive current.
MOSFETs have I 2 R losses, plus the P MAIN equation
includes an additional term for transition losses that are
highest at high output voltages. For V IN < 20V the high
current efficiency generally improves with larger MOSFETs,
while for V IN > 20V the transition losses rapidly increase to
the point that the use of a higher R DS(ON) device with lower
C RSS actual provides higher efficiency. The diode losses
are greatest at high input voltage or during a short circuit
when the diode duty cycle is nearly 100%.
The term (1+ δ ) is generally given for a MOSFET in the form
of a normalized R DS(ON) vs Temperature curve, but
δ = 0.005/ ° C can be used as an approximation for low
voltage MOSFETs. C RSS is usually specified in the MOSFET
8
characteristics. The constant k = 2.5 can be used to
estimate the contributions of the two terms in the P MAIN
dissipation equation.
Step-Down Converter: Output Diode Selection (D1)
The Schottky diode D1 shown in Figure 1 conducts during
the off-time. It is important to adequately specify the diode
peak current and average power dissipation so as not to
exceed the diode ratings.
The most stressful condition for the output diode is under
short circuit (V OUT = 0V). Under this condition, the diode
must safely handle I SC(PK) at close to 100% duty cycle.
Under normal load conditions, the average current con-
ducted by the diode is simply:
? ?
? ?
? V IN + V D ?
Remember to keep lead lengths short and observe proper
grounding (see Board Layout Checklist) to avoid ringing
and increased dissipation.
The forward voltage drop allowable in the diode is calcu-
lated from the maximum short-circuit current as:
V D ≈ ?
I SC AVG ?
where P D is the allowable diode power dissipation and will
be determined by efficiency and/or thermal requirements
(see Efficiency Considerations).
Step-Down Converter: C IN and C OUT Selection
In continuous mode the source current of the top
N-channel MOSFET is a square wave of approximate duty
cycle V OUT /V IN . To prevent large voltage transients, a low
ESR input capacitor sized for the maximum RMS current
must be used. The maximum RMS capacitor current is
given by:
1 / 2
OUT IN ? V OUT
C IN Required I RMS ≈ I MAX
V IN
This formula has a maximum at V IN = 2V OUT , where
I RMS = I OUT /2. This simple worst-case condition is com-
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3785IUF#TRPBF | IC REG CTRLR BST PWM VM 24-QFN |
| LTC3855IFE#TRPBF | IC REG CTRLR BUCK PWM CM 38TSSOP |
| LT3748HMS#TRPBF | IC REG CTRLR FLYBK ISO CM 16MSOP |
| LTC1628CG | IC REG CTRLR BUCK PWM CM 28-SSOP |
| VI-271-EW-F2 | CONVERTER MOD DC/DC 12V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1624IS8#PBF | 功能描述:IC REG CTRLR BST FLYBK INV 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC1624IS8#PBF | 制造商:Linear Technology 功能描述:DC/DC Converter IC |
| LTC1624IS8#TR | 功能描述:IC REG CTRLR BST FLYBK INV 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1624IS8#TRPBF | 功能描述:IC REG CTRLR BST FLYBK INV 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1624IS8PBF | 制造商:Linear Technology 功能描述:N-Channel Sw. Regulator Controller SOIC8 |
发布紧急采购，3分钟左右您将得到回复。