- 您现在的位置：买卖IC网 > PDF目录44988 > LTC1643HCGN#PBF (LINEAR TECHNOLOGY CORP) 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 PDF资料下载
参数资料
| 型号： | LTC1643HCGN#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| 封装： | 0.150 INCH, PLASTIC, SSOP-16 |
| 文件页数： | 3/16页 |
| 文件大小： | 278K |
| 代理商： | LTC1643HCGN#PBF |
11
LTC1643L/LTC1643L-1/LTC1643H
APPLICATIONS INFORMATION
WU
U
Timer
During a power-up sequence, a 20
A current source is
connected to the TIMER pin (Pin 4) and current limit faults
are ignored until the voltage ramps to within 0.9V of 12VIN
(Pin 1). This feature allows the chip to power up a PCI slot
that can accept boards with widely varying capacitive
loads on the supplies. The power-up time will be:
t
CV
II
ON
SUPPLY
LIMIT
LOAD
2
For CSUPPLY = 2000F, VSUPPLY = 5V, ILIMIT = 7A, ILOAD
= 5A, the turn-on time will be ~10ms. The timer period
should be set longer than the maximum supply turn-on
time but short enough to not exceed the maximum safe
operating area of the pass transistor during a short circuit.
The timer period will be:
t
C
V
A
TIMER
=
.
11 1
22
For CTIMER = 0.1F, the timer period will be ~ 50ms. The
TIMER pin (Pin 4) is immediately pulled low when ON
(Pin 5) goes low.
Thermal Shutdown
The internal switches for the 12V and –12V supplies are
protected by an internal current limit and thermal shut-
down circuit. When the temperature of chip reaches
150
°C, all switches will be latched off and the FAULT pin
(Pin 6) will be pulled low.
Short-Circuit Protection
During a normal power-up sequence, if the TIMER (Pin 4)
is done ramping and a supply is still in current limit, all of
the pass transistors will be immediately turned off and the
FAULT pin (Pin 6) will be pulled low as shown in Figure 4.
If a short circuit occurs after the supplies are powered up,
the shorted supply’s current will drop immediately to the
limit value (Figure 5).
If the supply remains in current limit for more than 15
s,
all of the supplies will be latched off. The 15
s delay
prevents quick current spikes—for example, from a fan
turning on—from causing false trips of the circuit breaker.
The chip will stay in the latched-off state until ON (Pin 5)
is cycled low then high, or the 12VIN pin (Pin 1) power
supply is cycled.
To prevent excessive power dissipation in the pass tran-
sistors and to prevent voltage spikes on the supplies
during short-circuit conditions, the current limit on each
supply is designed to be a function of the output voltage.
As the output voltage drops, the current limit decreases.
Unlike a traditional circuit breaker function where huge
currents can flow before the breaker trips, the current
foldback feature assures that the supply current will be
kept at a safe level and prevent voltage glitches when
powering up into a short.
The current limit for the 5V and 3.3V supplies is set by
placing a sense resistor between 5VIN (Pin 13) and 5VSENSE
(Pin 12) and between 3VIN (Pin 9) and 3VSENSE (Pin 10).
The current limit will be set by:
ILIMIT = 53mV/RSENSE
For a 0.005
resistor, the current limit will be set at 10.6A
and fold back to 1.5A when the output is shorted. For a
0.007
resistor, the current limit will be set at 7.6A and
fold back to 1.1A when the output is shorted.
The current limit for the internal 12V switch is set at
850mA folding back to 250mA and the –12V switch at
450mA folding back to 160mA.
In systems where it is possible to exceed the current limit
for a short amount of time, it might be necessary to
prevent the analog current loop from responding quickly
so the output voltage does not droop. This can be accom-
plished by adding an RC filter across the sense resistor as
shown in Figure 6. R4 should be 20
or less to prevent
offset errors. A 0.1
F capacitor gives a delay of about
1.5
s and a 1F capacitor gives a delay of about 15s.
CompactPCI Application
The LTC1643L is designed for hot swapping CompactPCI
boards. The typical application is shown in Figure 7. The
3.3V, 5V, 12V and –12V inputs to the LTC1643L come
from the medium length power pins. The long 3.3V, 5V and
V(I/O) pins power up the pull-up resistors, bus precharge
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1643LCGN#TR | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC1728HS5-5 | 3-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| LTC1729CS8-8.4#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC1772BIS6#PBF | 1 A SWITCHING CONTROLLER, 650 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC1871EMS#PBF-1 | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1643L-1CGN | 制造商:Linear Technology 功能描述: |
| LTC1643LCGN | 制造商:Linear Technology 功能描述: 制造商:Linear Technology 功能描述:POWER CONTROL/MANAGEMENT, 16 Pin, Plastic, SSOP |
| LTC1643LCGN#PBF | 制造商:Linear Technology 功能描述:Hot Swap Controller 16-Pin SSOP N |
| LTC1644CGN | 功能描述:IC CONTROLLER HOT SWAP 20-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC1644CGN#PBF | 功能描述:IC CONTROLLER HOT SWAP 20-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。