- 您现在的位置：买卖IC网 > PDF目录8895 > LTC1666CG#PBF (Linear Technology)IC D/A CONV 12BIT 50MSPS 28-SSOP PDF资料下载
参数资料
| 型号： | LTC1666CG#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 4/24页 |
| 文件大小： | 0K |
| 描述： | IC D/A CONV 12BIT 50MSPS 28-SSOP |
| 标准包装： | 47 |
| 设置时间： | 20ns |
| 位数： | 12 |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 电压电源： | 双 ± |
| 功率耗散（最大）： | 180mW |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
| 输出数目和类型： | 2 电流，单极 |
| 采样率（每秒）： | 50M |
| 产品目录页面： | 1352 (CN2011-ZH PDF) |
12
LTC1666/LTC1667/LTC1668
Adjusting the Full-Scale Output
In Figure 2, a serial interfaced DAC is used to set IOUTFS.
The LTC1661 is a dual 10-bit VOUT DAC with a buffered
voltage output that swings from 0V to VREF.
DAC Transfer Function
The LTC1666/LTC1667/LTC1668 use straight binary digital
coding. The complementary current outputs, IOUTA andIOUT
B, sink current from 0 to IOUTFS. For IOUTFS = 10mA (nomi-
nal), IOUT A swings from 0mA when all bits are low (e.g.,
Code = 0) to 10mA when all bits are high (e.g., Code = 65535
for LTC1668) (decimal representation). IOUT B is comple-
mentary to IOUTA. IOUTA and IOUTB are given by the following
formulas:
LTC1666:
IOUT A = IOUTFS (DAC Code/4096)
(2)
IOUT B = IOUTFS (4095 – DAC Code)/4096
(3)
LTC1667:
IOUT A = IOUTFS (DAC Code/16384)
(4)
IOUT B = IOUTFS (16383 – DAC Code)/16384
(5)
LTC1668:
IOUT A = IOUTFS (DAC Code/65536)
(6)
IOUT B = IOUTFS (65535 – DAC Code)/65536
(7)
In typical applications, the LTC1666/LTC1667/LTC1668
differential output currents either drive a resistive load
directly or drive an equivalent resistive load through a
transformer, or as the feedback resistor of an I-to-V
converter. The voltage outputs generated by the IOUT A and
IOUT B output currents are then:
Figure 2. Adjusting the Full-Scale Current of
the LTC1666/LTC1667/LTC1668 with a DAC
APPLICATIO S I FOR ATIO
WU
UU
VOUT A = IOUT A RLOAD
(8)
VOUT B = IOUT B RLOAD
(9)
The differential voltage is:
VDIFF = VOUT A – VOUT B
(10)
= (IOUT A – IOUT B) (RLOAD)
Substituting the values found earlier for IOUT A, IOUT B and
IOUTFS (LTC1668):
VDIFF = {2 DAC Code – 65535)/65536} 8
(RLOAD/RSET) (VREF)
(11)
From these equations some of the advantages of differen-
tial mode operation can be seen. First, any common mode
noise or error on IOUTA and IOUTB is cancelled. Second, the
signal power is twice as large as in the single-ended case.
Third, any errors and noise that multiply times IOUT A and
IOUT B, such as reference or IOUTFS noise, cancel near
midscale, where AC signal waveforms tend to spend the
most time. Fourth, this transfer function is bipolar; e.g. the
output swings positive and negative around a zero output
at mid-scale input, which is more convenient for AC
applications.
Note that the term (RLOAD/RSET) appears in both the
differential and single-ended transfer functions. This means
that the Gain Error of the DAC depends on the ratio of
RLOAD to RSET, and the Gain Error tempco is affected by the
temperature tracking of RLOAD with RSET. Note also that
the absolute tempco of RLOAD is very critical for DC
nonlinearity. As the DAC output changes from 0mA to
10mA the RLOAD resistor will heat up slightly, and even a
very low tempco can produce enough INL bowing to be
significant at the 16-bit level. This effect disappears with
medium to high frequency AC signals due to the slow
thermal time constant of the load resistor.
Analog Outputs
The LTC1666/LTC1667/LTC1668 have two complemen-
tary current outputs, IOUT A and IOUT B (see DAC Transfer
Function). The output impedance of IOUT A and IOUT B
(RIOUT A and RIOUT B) is typically 1.1k to LADCOM. (See
Figure 3.)
+
–
IREFIN
2.5V
REFERENCE
RSET
1.9k
REF
0.1
F
1/2 LTC1661
5V
1666/7/8 F03
LTC1666/
LTC1667/
LTC1668
相关PDF资料 |
PDF描述 |
|---|---|
| MS27474T12B3PLC | CONN HSG RCPT 3POS JAM NUT PINS |
| MS27473E14A18SLC | CONN HSG PLUG 18POS STRGHT SCKT |
| VI-214-MW-F2 | CONVERTER MOD DC/DC 48V 100W |
| VI-214-MW-F1 | CONVERTER MOD DC/DC 48V 100W |
| MS27473T20A16PLC | CONN HSG PLUG 16POS STRGHT PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1666IG | 功能描述:IC D/A CONV 12BIT 50MSPS 28-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
| LTC1666IG#PBF | 功能描述:IC D/A CONV 12BIT 50MSPS 28-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
| LTC1666IG#TR | 功能描述:IC D/A CONV 12BIT 50MSPS 28-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
| LTC1666IG#TRPBF | 功能描述:IC D/A CONV 12BIT 50MSPS 28-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
| LTC1667CG | 功能描述:IC D/A CONV 14BIT 50MSPS 28-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
发布紧急采购，3分钟左右您将得到回复。