参数资料
型号: LTC1682IS8-5#PBF
厂商: Linear Technology
文件页数: 10/12页
文件大小: 0K
描述: IC REG MULTI CONFIG 5V 8SOIC
标准包装: 100
类型: 升压(升压),切换电容(充电泵),倍增器
输出类型: 固定
输出数: 1
输出电压: 5V
输入电压: 1.8 V ~ 4.4 V
PWM 型: Burst Mode?
频率 - 开关: 550kHz
电流 - 输出: 90mA
同步整流器:
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
包装: 管件
供应商设备封装: 8-SOIC
产品目录页面: 1339 (CN2011-ZH PDF)
LTC1682/LTC1682-3.3/LTC1682-5
APPLICATIO N S I N FOR M ATIO N
Power-On Reset
Upon initial power-up, a power-on reset circuit ensures
that the internal functions are correctly initialized when
power is applied. Once V IN reaches approximately 1V, the
power-on reset circuit will enable the part as long as the
SHDN pin is held high.
Thermal Considerations
The power handling capability of the device will be limited
by the maximum rated junction temperature (125 ° C). The
device power dissipation P D = I OUT (2V IN – V OUT ) +
V IN (4mA). The device dissipates the majority of its heat
through its pins, especially GND (Pin 4). Thermal resis-
tance to ambient can be optimized by connecting GND to
a large copper region on the PCB, which serves as a heat
sink. Applications which operate the LTC1682 near maxi-
mum power levels should maximize the copper area at all
pins except C + , C – and FILT/FB and ensure that there is
some airflow over the part to carry away excess heat.
General Layout Considerations
Due to the high switching frequency and high transient
currents produced by the device, careful board layout is a
must. A clean board layout using a ground plane and short
connections to all capacitors will improve noise perfor-
mance and ensure proper regulation (Figure 5).
The FILT pin on the LTC1682-3.3/LTC1682-5 is a high
impedance node. Leakage currents at this pin must be
minimized.
Measuring Output Noise
Measuring the LTC1682 low noise levels requires care.
Figure 6 shows a test setup for taking the measurement.
Good connection and signal handling technique should
yield about 500 μ V P-P over a 2.5MHz bandwidth. The noise
measurement involves AC coupling the LTC1682 output
into the test setup’s input and terminating this connection
with 50 ? . Coaxial connections must be maintained to
preserve measurement integrity.
C2
V OUT
1
8
C3
SHDN
2
3
LTC1682-3.3/5
7 V IN
6
C FILT
4
5
C4
GND
C1
1682 F05
Figure 5
BNC CABLES
OR COUPLERS
COUPLING
CAPACITOR
PREAMPLIFIER
BATTERY OR
LOW NOISE DC
POWER SUPPLY
LTC1682 V OUT
DEMO
BOARD
R LOAD
R*
1822
20dB
BANDWIDTH
FILTER
INPUT
OSCILLOSCOPE
CONNECT BNC AND
R*
1682 F06
R LOAD GROUND TO THE
OUTPUT CAPACITOR
GROUND TERMINAL E5
PLACE COUPLING
CAPACITOR IN SHIELDED
BOX WITH COAXIAL
CONNECTOR
R*
*50 ? TERMINATIONS
HP-11048C OR
PLACE BANDWIDTH FILTER
COMPONENTS IN SHIELDED BOX
WITH COAXIAL CONNECTORS
NOTE: KEEP BNC CONNECTIONS
AS SHORT AS POSSIBLE
EQUIVALENT
Figure 6. LTC1682 Noise Measurement Test Setup
10
相关PDF资料
PDF描述
MAX6463UK34+T IC VOLT DETECTOR LP SOT23-5
LT1307CS8#PBF IC REG BOOST 3.3V/5V 0.1A 8SOIC
MAX6463UK35+T IC VOLT DETECTOR LP SOT23-5
LT1307BCS8#PBF IC REG BOOST 3.3V/5V 0.1A 8SOIC
GBC36DCST-S288 CONN EDGECARD 72POS .100 EXTEND
相关代理商/技术参数
参数描述
LTC1685CS8 功能描述:IC TXRX RS485 PREC DELAY 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232,RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC(0.295",7.50mm 宽) 供应商设备封装:28-SOIC 包装:管件
LTC1685CS8#PBF 功能描述:IC TXRX RS485 PREC DELAY 8-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 产品培训模块:RS-232 & USB Transceiver 标准包装:2,000 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SSOP(0.209",5.30mm 宽) 供应商设备封装:16-SSOP 包装:带卷 (TR) 其它名称:296-19849-2
LTC1685CS8#TR 功能描述:IC TXRX RS485 PREC DELAY 8SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232,RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC(0.295",7.50mm 宽) 供应商设备封装:28-SOIC 包装:管件
LTC1685CS8#TRPBF 功能描述:IC TXRX RS485 PREC DELAY 8-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232,RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC(0.295",7.50mm 宽) 供应商设备封装:28-SOIC 包装:管件
LTC1685CS830506PBF 制造商:Linear Technology 功能描述: