- 您现在的位置：买卖IC网 > PDF目录20625 > LTC1704BEGN#PBF (Linear Technology)IC REG DL BUCK/LINEAR 16-SSOP PDF资料下载
参数资料
| 型号： | LTC1704BEGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/28页 |
| 文件大小： | 347K |
| 描述： | IC REG DL BUCK/LINEAR 16-SSOP |
| 标准包装： | 100 |
| 拓扑： | 降压（降压）（1），线性（LDO）（1） |
| 功能： | 任何功能 |
| 输出数： | 2 |
| 频率 - 开关： | 550kHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 控制器 |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 3.15 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC1704/LTC1704B
11
1704bfa
APPLICATIO S I FOR ATIO
U
U
U
Overcurrent protection is achieved by limiting the drive
current. The input current at the REGILM pin programs the
current limit threshold. Refer to the Linear Regulator
Supply Current Limit Programming section for more
information on choosing R
REGILM
. The linear regulator
controller employs a foldback current limit scheme for
overcurrent protection. Under a short-circuit condition,
the external NPN transistor is subjected to the full input
voltage across its collector-emitter terminal. This increases
the power dissipation of the NPN and may eventually
cause damage to the transistor. LTC1704 overcomes this
problem by using a foldback current limit scheme whereby
the available drive current is reduced as the output voltage
at REGFB pin drops. This limits the power dissipation and
prevents catastrophic damage to the external NPN.
ARCHITECTURE DETAILS
Switcher Supply Architecture
The LTC1704 switcher supply is designed to operate as a
synchronous buck converter (Figure 1). The controller
includes two high power MOSFET gate drivers to control
the external N-channel MOSFETs QT and QB. The drivers
have 0.5& output impedances and can carry over an amp
of continuous current with peak currents up to 5A to slew
large MOSFET gates quickly. The drain of QT is connected
to the input supply and the source of QT connected to the
switching node SW. QB is the synchronous rectifier with
its drain at SW and its source at PGND. SW is connected
to one end of the inductor, with the other end connected
to V
OUTSW
. The output capacitor is connected from V
OUTSW
to PGND.
When a switching cycle begins, QB is turned off and QT is
turned on. SW rises almost immediately to V
IN
and the
inductor current begins to increase. When the PWM pulse
completes, QT turns off and one nonoverlap interval later,
QB turns on. Now SW drops to PGND and the inductor
current decreases. The cycle repeats with the next tick of
the master clock. The percentage of time spent in each
mode is controlled by the duty cycle of the PWM signal,
which in turn is controlled by the feedback amplifier. The
master clock runs at a 550kHz rate and turns QT once
every 1.8祍. In a typical application with a 5V input and a
1.5V output, the duty cycle will be set at 1.5/5 " 100% or
30% by the feedback loop. This will give roughly a 540ns
on-time for QT and a 1.26祍 on-time for QB.
This constant frequency operation brings with it a couple
of benefits. Inductor and capacitor values can be chosen
with a precise operating frequency in mind and the feed-
back loop components can be similarly tightly specified.
Noise generated by the circuit will always be in a known
frequency band with the 550kHz frequency designed to
leave the 455kHz IF band free of interference. Subharmonic
oscillation and slope compensation, common headaches
with constant frequency current mode switchers, are
absent in voltage mode designs like the LTC1704. During
the time that QT is on, its source (the SW pin) is at V
IN
. V
IN
is also the power supply for the LTC1704. However, QT
requires V
IN
+ V
GS(ON)
at its gate to achieve minimum R
ON
.
The LTC1704, needs to generate a gate drive signal at TG
higher than its highest supply voltage. To accomplish this,
the TG driver runs from floating supplies, with its negative
supply attached to SW and its power supply at BOOST.
This allows it to slew up and down with the source of QT.
Figure 1. Synchronous Buck Architecture
TG
SW
BG
PGND
LTC1704
QT
C
IN
QB
L
+
C
OUTSW
1704 F01
V
OUTSW
V
IN
+
Figure 2. Floating TG Driver Supply
TG
C
CP
D
CP
BOOST
SW
BG
PGND
PV
CC
LTC1704
QT
C
IN
QB
L
+
C
OUTSW
1704 F02
V
OUTSW
V
IN
+
相关PDF资料 |
PDF描述 |
|---|---|
| EEM06DTMI-S189 | CONN EDGECARD 12POS R/A .156 SLD |
| ECM08DCTI | CONN EDGECARD 16POS DIP .156 SLD |
| CS5464-ISZR | IC ENERGY METERING 1PHASE 28SSOP |
| ISL6610AIBZ-T | IC MOSFET DRVR DUAL SYNC 14-SOIC |
| RCM06DTAI-S189 | CONN EDGECARD 12POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1704EGN | 功能描述:IC REG DL BUCK/LINEAR 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LTC1704EGN#PBF | 功能描述:IC REG DL BUCK/LINEAR 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LTC1704EGN#TR | 功能描述:IC REG DL BUCK/LINEAR 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LTC1704EGN#TRPBF | 功能描述:IC REG DL BUCK/LINEAR 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LTC1705EGN | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。