- 您现在的位置：买卖IC网 > PDF目录16308 > LTC1733EMSE#PBF (Linear Technology)IC CHRGR BATT MONO THERML 10MSOP PDF资料下载
参数资料
| 型号： | LTC1733EMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC CHRGR BATT MONO THERML 10MSOP |
| 标准包装： | 50 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.5 V ~ 6.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 10-MSOP 裸露焊盘 |
| 包装： | 管件 |
| 产品目录页面： | 1340 (CN2011-ZH PDF) |
LTC1733
OPERATIO
The LTC1733 is a linear battery charger designed primarily
for charging single cell lithium-ion batteries. Featuring an
internal P-channel power MOSFET, the charger uses a
constant-current/constant-voltage charge algorithm with
programmable current and a programmable timer for
charge termination. Charge current can be programmed
up to 1.5A with a final float voltage accuracy of ± 1%. No
blocking diode or sense resistor is required thus dropping
the external component count to three for the basic
charger circuit. The CHRG, ACPR, and FAULT open-drain
status outputs provide information regarding the status of
the LTC1733 at all times. An NTC thermistor input
provides the option of charge qualification using battery
temperature.
An internal thermal limit reduces the programmed charge
current if the die temperature attempts to rise above a
preset value of approximately 105 ° C. This feature protects
the LTC1733 from excessive temperature, and allows the
user to push the limits of the power handling capability of
a given circuit board without risk of damaging the LTC1733
or the external components. Another benefit of the LTC1733
thermal limit is that charge current can be set according to
typical, not worst-case, ambient temperatures for a given
application with the assurance that the charger will auto-
matically reduce the current in worst-case conditions.
The charge cycle begins when the voltage at the V CC pin
rises above the UVLO level and a program resistor is
connected from the PROG pin to ground. At the beginning
of the charge cycle, if the battery voltage is below 2.48V,
the charger goes into trickle charge mode to bring the cell
voltage up to a safe level for charging. The charger goes
into the fast charge constant-current mode once the
voltage on the BAT pin rises above 2.48V. In constant-
current mode, the charge current is set by R PROG .
When the battery approaches the final float voltage, the
charge current begins to decrease as the LTC1733 switches
to constant-voltage mode. When the current drops to 10%
of the full-scale charge current, an internal comparator
latches off the MOSFET at the CHRG pin and connects a
weak current source to ground to indicate a near end-of-
charge (C/10) condition. The C/10 latch can be cleared by
momentarily pulling the PROG pin above the 2.15V
shutdown threshold, or momentarily removing and reap-
plying V CC .
An external capacitor on the TIMER pin sets the total
charge time. When this time elapses the charge cycle
terminates and the CHRG pin assumes a high impedance
state. To restart the charge cycle, simply remove the input
voltage and reapply it, or force the PROG pin above the
2.15V shutdown threshold (note: simply floating the PROG
pin will not restart the charging cycle.
For lithium-ion and similar batteries that require accurate
final float potential, the internal reference, voltage ampli-
fier and the resistor divider provide regulation with ± 1%
(max) accuracy.
When the input voltage is not present, the charger goes
into a sleep mode, dropping battery drain current, I BAT , to
less than 5 μ A. This greatly reduces the current drain on the
battery and increases the standby time. The charger can be
shut down (I CC = 0.9mA) by forcing the PROG pin above
2.15V.
sn1733 1733fs
8
相关PDF资料 |
PDF描述 |
|---|---|
| EBM36DCTH-S288 | CONN EDGECARD 72POS .156 EXTEND |
| LTC4002ES8-8.4#PBF | IC CHARGER BATTERY LI-ION 8-SOIC |
| EBM36DCTD-S288 | CONN EDGECARD 72POS .156 EXTEND |
| ESA14DRMN-S288 | CONN EDGECARD 28POS .125 EXTEND |
| 3-1906012-8 | CA 2.0MM OFNR 50/125,LC SEC RED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1734ES6-4.1#TR | 功能描述:IC BATT CHRGR LI-ION LIN SOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1734ES6-4.1#TRM | 功能描述:IC BATT CHRGR LI-ION LIN SOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1734ES6-4.1#TRMPBF | 功能描述:IC BATT CHRGR LI-ION LIN SOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1734ES6-4.1#TRPBF | 功能描述:IC BATT CHRGR LI-ION LIN SOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1734ES6-4.2 | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion/NiCD/NiMH 200mA to 700mA 4.2V 6-Pin TSOT-23 制造商:Linear Technology 功能描述:0.9 A BATTERY CHARGE CONTROLLER, PDSO6 |
发布紧急采购，3分钟左右您将得到回复。