- 您现在的位置：买卖IC网 > PDF目录16037 > LTC1733EMSE#TR (Linear Technology)IC CTRLR BATT CHRG LI-ION 10MSOP PDF资料下载
参数资料
| 型号： | LTC1733EMSE#TR |
| 厂商： | Linear Technology |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR BATT CHRG LI-ION 10MSOP |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.5 V ~ 6.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 10-MSOP 裸露焊盘 |
| 包装： | 带卷 (TR) |
LTC1733
APPLICATIO S I FOR ATIO
Open-Drain Status Outputs
The LTC1733 has three open-drain status outputs: ACPR,
V +
8
V DD
CHRG and FAULT. The ACPR pin pulls low when an input
voltage greater than the undervoltage lockout threshold is
applied and goes high impedance when power (V IN < V UV )
V CC
LTC1733
CHRG
3
400k
2k
μ PROCESSOR
OUT
is removed. CHRG and FAULT work together to indicate
the status of the charge cycle. Table 1 describes the status
of the charge cycle based on the CHRG and FAULT
outputs.
Table 1.
IN
1733 F02
Figure 2. Microprocessor Interface
FAULT
High
Low
High
Low
High
Low
CHRG
Low
Low
25 μ A
pulldown
25 μ A
pulldown
High
High
Description
Charge cycle has started, C/10 has not been
reached and charging is proceeding normally.
Charge cycle has started, C/10 has not been
reached, but the charge current and timer
have been paused due to an NTC out-of-
temperature condition.
C/10 has been reached and charging is
proceeding normally.
C/10 has been reached but the charge current
and timer have paused due to an
NTC out-of-temperature condition.
Normal timeout (charging has terminated).
If FAULT goes low and CHRG goes high
impedance simultaneously, then the LTC1733
has timed out due to a bad cell (V BAT <2.48V
after one-quarter the programmed charge time).
If CHRG goes high impedance first, then
When the LTC1733 is in charge mode, the CHRG pin is
pulled low by the internal N-channel MOSFET. To detect
this mode, force the digital output pin, OUT, high and
measure the voltage at the CHRG pin. The N-channel
MOSFET will pull the pin low even with the 2k pull-up
resistor. Once the charge current drops to 10% of the full-
scale current (C/10), the N-channel MOSFET is turned off
and a 25 μ A current source is connected to the CHRG pin.
The IN pin will then be pulled high by the 2k pull-up. By
forcing the OUT pin to a high impedance state, the current
source will pull the pin low through the 400k resistor.
When the internal timer has expired, the CHRG pin will
assume a high impedance state and the 400k resistor will
then pull the pin high to indicate that charging has termi-
nated.
the LTC1733 has timed out normally (charging
has terminated), but NTC is indicating an out-
of-temperature condition.
CHRG Status Output Pin
When the charge cycle starts, the CHRG pin is pulled to
ground by an internal N-channel MOSFET capable of
driving an LED. When the charge current drops to 10% of
the full-scale current (C/10), the N-channel MOSFET is
latched off and a weak 25 μ A current source to ground is
connected to the CHRG pin. After a time-out occurs, the
pin assumes a high impedance state. By using two differ-
ent value pull-up resistors a microprocessor can detect
three states from this pin (charging, C/10, and time-out).
See Figure 2.
NTC Thermistor
The battery temperature is measured by placing a negative
temperature coefficient (NTC) thermistor close to the
battery pack. The NTC circuitry is shown in Figure 3. To use
this feature, connect a 10k NTC thermistor between the
NTC pin and ground and a resistor (R HOT ) from the NTC pin
to V CC . R HOT should be a 1% resistor with a value equal to
the value of the chosen NTC thermistor at 50 ° C (this value
is 4.1k for a Vishay NTHS0603N02N1002J thermistor).
The LTC1733 goes into hold mode when the resistance of
the NTC thermistor drops below 4.1k which should be
at 50 ° C. The hold mode freezes the timer and stops
the charge cycle until the thermistor indicates a return
to a valid temperature. As the temperature drops, the
sn1733 1733fs
10
相关PDF资料 |
PDF描述 |
|---|---|
| GEM25DTMN-S189 | CONN EDGECARD 50POS R/A .156 SLD |
| RS80E471MDNASQJT | CAP ALUM 470UF 2.5V 20% RADIAL |
| RBM08DTMD-S189 | CONN EDGECARD 16POS R/A .156 SLD |
| M3DGK-4036J | IDC CABLE - MKR40K/MC40G/MCS40K |
| RBM08DTMN-S189 | CONN EDGECARD 16POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1734ES6-4.1#TR | 功能描述:IC BATT CHRGR LI-ION LIN SOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1734ES6-4.1#TRM | 功能描述:IC BATT CHRGR LI-ION LIN SOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1734ES6-4.1#TRMPBF | 功能描述:IC BATT CHRGR LI-ION LIN SOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1734ES6-4.1#TRPBF | 功能描述:IC BATT CHRGR LI-ION LIN SOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1734ES6-4.2 | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion/NiCD/NiMH 200mA to 700mA 4.2V 6-Pin TSOT-23 制造商:Linear Technology 功能描述:0.9 A BATTERY CHARGE CONTROLLER, PDSO6 |
发布紧急采购，3分钟左右您将得到回复。