参数资料
| 型号： | LTC1744IFW#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 50MSPS 48-TSSOP |
| 标准包装： | 1,800 |
| 位数： | 14 |
| 采样率（每秒）： | 50M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 1.5W |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-TFSOP（0.240"，6.10mm 宽） |
| 供应商设备封装： | 48-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 2 个单端，双极；1 个差分，双极 |
11
LTC1744
1744f
APPLICATIO S I FOR ATIO
WU
U
2, 3, etc. The 3rd order intermodulation products are 2fa
+ fb, 2fb + fa, 2fa – fb and 2fb – fa. The intermodulation
distortion is defined as the ratio of the RMS value of either
input tone to the RMS value of the largest 3rd order
intermodulation product.
Spurious Free Dynamic Range (SFDR)
Spurious free dynamic range is the peak harmonic or
spurious noise that is the largest spectral component
excluding the input signal and DC. This value is expressed
in decibels relative to the RMS value of a full scale input
signal.
Input Bandwidth
The input bandwidth is that input frequency at which the
amplitude of the reconstructed fundamental is reduced by
3dB for a full scale input signal.
Aperture Delay Time
The time from when a rising ENC equals the ENC voltage
to the instant that the input signal is held by the sample and
hold circuit.
Aperture Delay Jitter
The variation in the aperture delay time from conversion to
conversion. This random variation will result in noise
when sampling an AC input. The signal to noise ratio due
to the jitter alone will be:
SNRJITTER = –20log (2π) FIN TJITTER
CONVERTER OPERATION
As shown in Figure 1, the LTC1744 is a CMOS pipelined
multistep converter. The converter has four pipelined
ADC stages; a sampled analog input will result in a
digitized value five cycles later, see the Timing Diagram
section. The analog input is differential for improved
common mode noise immunity and to maximize the input
range. Additionally, the differential input drive will reduce
even order harmonics of the sample-and-hold circuit. The
encode input is also differential for improved common
mode noise immunity.
DYNAMIC PERFORMANCE
Signal-to-Noise Plus Distortion Ratio
The signal-to-noise plus distortion ratio [S / (N + D)] is the
ratio between the RMS amplitude of the fundamental input
frequency and the RMS amplitude of all other frequency
components at the ADC output. The output is band limited
to frequencies above DC to below half the sampling
frequency.
Signal-to-Noise Ratio
The signal-to-noise ratio (SNR) is the ratio between the
RMS amplitude of the fundamental input frequency and
the RMS amplitude of all other frequency components
except the first five harmonics and DC.
Total Harmonic Distortion
Total harmonic distortion is the ratio of the RMS sum of all
harmonics of the input signal to the fundamental itself. The
out-of-band harmonics alias into the frequency band
between DC and half the sampling frequency. THD is
expressed as:
THD
Log
VVV
Vn
V
=
++
+
20
23
4
1
22
2
...
where V1 is the RMS amplitude of the fundamental fre-
quency and V2 through Vn are the amplitudes of the
second through nth harmonics. The THD calculated in this
data sheet uses all the harmonics up to the fifth.
Intermodulation Distortion
If the ADC input signal consists of more than one spectral
component, the ADC transfer function nonlinearity can
produce intermodulation distortion (IMD) in addition to
THD. IMD is the change in one sinusoidal input caused by
the presence of another sinusoidal input at a different
frequency.
If two pure sine waves of frequencies fa and fb are applied
to the ADC input, nonlinearities in the ADC transfer
function can create distortion products at the sum and
difference frequencies of mfa
±nfb, where m and n = 0, 1,
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1745CFW#TRPBF | IC ADC 12BIT 25MSPS LN 48TSSOP |
| LTC1746IFW#TRPBF | IC ADC 14BIT 25MSPS LP 48TSSOP |
| LTC1747IFW#PBF | IC ADC 12BIT 80MSPS 48-TSSOP |
| LTC1748CFW#TRPBF | IC ADC 14BIT 80MSPS 48-TSSOP |
| LTC1749IFW#PBF | IC ADC 12BIT 80MSPS SMPL 48TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1745CFW | 功能描述:IC ADC 12BIT 25MSPS LN 48TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC1745CFW#PBF | 功能描述:IC ADC 12BIT 25MSPS LN 48TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| LTC1745CFW#TR | 功能描述:IC ADC SMPL 12BIT 25MSPS 48TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC1745CFW#TRPBF | 功能描述:IC ADC 12BIT 25MSPS LN 48TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| LTC1745IFW | 功能描述:IC ADC SMPL 12BIT 25MSPS 48TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。