- 您现在的位置：买卖IC网 > PDF目录22190 > LTC1968CMS8#PBF (Linear Technology)IC CONVERTER RMS-DC PREC 8MSOP PDF资料下载
参数资料
| 型号： | LTC1968CMS8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/28页 |
| 文件大小： | 296K |
| 描述： | IC CONVERTER RMS-DC PREC 8MSOP |
| 标准包装： | 50 |
| 电流 - 电源： | 2.3mA |
| 电源电压： | 5.0V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
| 产品目录页面： | 1338 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
12
LTC1968
1968f
Input Connections
The LTC1968 input is differential and DC coupled. The
LTC1968 responds to the RMS value of the differential
voltage between Pin 2 and Pin 3, including the DC portion
of that difference. However, there is no DC-coupled path
from the inputs to ground. Therefore, at least one of the two
inputs must be connected with a DC-return path to ground.
Both inputs must be connected to something. If either
input is left floating, a zero volt output will result.
For single-ended DC-coupled applications, simply con-
nect one of the two inputs (they are interchangeable) to
the signal, and the other to ground. This will work well for
dual supply configurations, but for single supply con-
figurations it will only work well for unipolar input sig-
nals. The LTC1968 input voltage range is from rail-to-rail,
and when the input is driven above V
+
or below GND the
gain and offset errors will increase substantially after just
a few hundred millivolts of overdrive. Fortunately, most
single supply circuits measuring a DC-coupled RMS
value will include some reference voltage other than
ground, and the second LTC1968 input can be connected
to that point.
For single-ended AC-coupled applications, Figure 9 shows
three alternate topologies. The first one, shown in Figure
9a uses a coupling capacitor to one input while the other
is grounded. This will remove the DC voltage difference from
the input to the LTC1968, and it will therefore not be part
of the resulting output voltage. Again, this connection will
APPLICATIO S I FOR ATIO
U
U
U
work well with dual supply configurations, but in single
supply configurations it will be necessary to raise the volt-
age on the grounded input to assure that the signal at the
active input stays within the range of 0V to V
+
. If there is
already a suitable voltage reference available, connect the
second input to that point. If not, a midsupply voltage can
be created with two resistors as shown in Figure 9b.
Finally, if the input voltage is known to be between 0V and
V
+
, it can be AC coupled by using the configuration shown
in Figure 9c. Whereas the DC return path was provided
through Pin 3 in Figures 9a and 9b, in this case, the return
path is provided on Pin 2, through the input signal volt-
ages. The switched capacitor action between the two input
pins of the LTC1968 will cause the voltage on the coupling
capacitor connected to the second input to follow the DC
average of the input voltage.
For differential input applications, connect the two inputs to
the differential signal. If AC coupling is desired, one of the
two inputs can be connected through a series capacitor.
In all of these connections, to choose the input coupling
capacitor, C
C
, calculate the low frequency coupling time
constant desired, and divide by the LTC1968 differential
input impedance. Because the LTC1968 input impedance
is about 100 times its output impedance, this capacitor is
typically much smaller than the output averaging capaci-
tor. Its requirements are also much less stringent, and a
ceramic chip capacitor will usually suffice.
Figure 9. Single-Ended AC-Coupled Input Connection Alternatives
+
LTC1968
GND
V
+
V
+
V
+
V
(9a)
C
C
IN1
V
IN
IN2
2
3
LTC1968
(9b)
C
C
R1
10k
R2
10k
0.1礔
IN1
V
IN
V
+
IN2
2
3
LTC1968
(9c)
C
C
IN1
V
IN
1968 F09
V
DC
IN2
2
3
相关PDF资料 |
PDF描述 |
|---|---|
| RAC20-05DA | CONV AC/DC 2A 6.5-18VIN 3.0-5.5V |
| 1N5398S-T | DIODE STD REC 1.5A 800V DO-41 |
| NCP612SQ28T2G | IC REG LDO 2.8V .2A SC70-5 |
| GCM06DSEI-S243 | CONN EDGECARD 12POS .156 EYELET |
| V150B48C250BL2 | CONVERTER MOD DC/DC 48V 250W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1968IMS8 | 功能描述:IC CONVERTER RMS-DC PREC 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - RMS 至 DC 转换器 系列:- 标准包装:46 系列:- 电流 - 电源:1.2mA 电源电压:±18 V，36 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:管件 |
| LTC1968IMS8#PBF | 功能描述:IC CONVERTER RMS-DC PREC 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - RMS 至 DC 转换器 系列:- 标准包装:46 系列:- 电流 - 电源:1.2mA 电源电压:±18 V，36 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:管件 |
| LTC1968IMS8#TR | 功能描述:IC CONVERTER RMS-DC PREC 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - RMS 至 DC 转换器 系列:- 标准包装:46 系列:- 电流 - 电源:1.2mA 电源电压:±18 V，36 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:管件 |
| LTC1968IMS8#TRPBF | 功能描述:IC CONVERTER RMS-DC PREC 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - RMS 至 DC 转换器 系列:- 标准包装:46 系列:- 电流 - 电源:1.2mA 电源电压:±18 V，36 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:管件 |
| LTC1980EGN | 功能描述:IC PWM BATT CHARGER/CONV 24-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。