- 您现在的位置：买卖IC网 > PDF目录15991 > LTC1980EGN#TR (Linear Technology)IC PWM BATT CHARGER/CONV 24-SSOP PDF资料下载
参数资料
| 型号： | LTC1980EGN#TR |
| 厂商： | Linear Technology |
| 文件页数： | 6/16页 |
| 文件大小： | 0K |
| 描述： | IC PWM BATT CHARGER/CONV 24-SSOP |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子，镍镉，镍氢 |
| 电源电压： | 2.85 V ~ 10 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 带卷 (TR) |
LTC1980
PI FU CTIO S
PROG (Pin 1): Charge Current Ratio Programming Pin.
Programs the full charge current when the charger is in the
constant current mode. A resistor placed between the
PROG pin and the PROGT pin (Pin 2) determines the
charge current. The PROG pin connects to an open drain
MOSFET which turns on for full current and is off when
trickle charging.
PROGT (Pin 2): Trickle Charge Programming Pin. Pro-
grams the trickle charge current for a deeply discharged
battery. Two resistors are used, one between the PROGT
pin and CA OUT (Pin 22) and another from PROGT to
ground. A capacitor between the PROGT pin and V C (Pin
4) provides compensation for the constant current feed-
back loop.
REGFB(Pin3): DC/DCConverterFeedbackPin.Thispinis
used to program the DC/DC converter output voltage when
the LTC1980 is in the DC/DC (regulator) converter mode.
An external resistor divider from V REG to REGFB to ground
V REG (Pin 7): Connection Point to the DC/DC Converter
Side of the Combo Charger/Converter Circuit.
WA (Pin 8): Wall Adapter Comparator Input. An external
resistor divider from the wall adapter output to WA to
ground sets the threshold which determines if charging
can occur. If the wall adapter is below this threshold, the
LTC1980 assumes the wall adapter is not present and the
charger shuts down. Wall adapter sense threshold is set
higher than the DC/DC converter output voltage to insure
correct operation.
BATT1 (Pin 9): Logic Input Pin for Selecting
Preprogrammed Li-Ion Charge Voltage. See Truth Table
logic settings.
BATT2 (Pin 10): Logic Input Pin for Selecting
Preprogrammed Li-Ion Charge Voltage. The following
combinations of BATT1 and BATT2 select the correct Li-
Ion charge voltage. See Truth Table.
programs the output voltage. The virtual reference voltage
(V REF ) on this pin is 1.225V. A series RC from the REGFB
pin to V C (Pin 4) provides pole-zero compensation for the
regulator outer loop.
V C (Pin 4): Control Signal of the Inner Loop of the Current
Mode PWM. A common current mode loop is used by the
BATT2
0
0
1
1
Don’t Care
BATT1
0
1
0
1
Open
FLOAT VOLTAGE
4.1V
4.2V
8.2V
8.4V
Externally Set Via OVP
battery charger and voltage regulator functions. Minimum
duty factor (measured on BGTDR (Pin 14) in regulator
mode and RGTDR (Pin 11) in charger mode) occurs at
approximately 1V. Duty factor increases as V C increases.
This part includes slope compensation, so there is some
variation in V C for minimum and maximum duty factor as
V REG or V BAT is varied.
LDOFB (Pin 5): Low Dropout Regulator Feedback Pin.
This pin is used to program the low dropout linear regula-
tor output voltage. An external resistor divider from the
output of the LDO regulator (drain of the external MOSFET)
to LDOFB to ground programs the output voltage. The
virtual reference voltage on this pin is 1.225V.
LDODRV (Pin 6): Low Dropout Error Amplifier Output.
This pin drives the gate of an external PMOS pass transis-
tor. This pin is pulled up to V REG (shutting off the pass
transistor) if MODE (Pin 16) is grounded or if undervoltage
Logic 1 = V BIAS2 (Pin 19), Logic 0 = GND
RGTDR (Pin 11): DC/DC Converter (Regulator) Side Gate
Drive Pin. This pin provides gate drive to the external
MOSFET (REG-FET) that connects to V REG via the trans-
former.
PGND (Pin 12): Power Ground. Refer to the Applications
Information section for proper use of ground and power
ground connections.
V BIAS1 (Pin 13): Internally Generated Power Bus. Bypass
this pin with a 1 μ F or larger ceramic capacitor (or other low
ESR capacitor) to PGND (Pin 12). Do not connect any load
to this pin.
BGTDR (Pin 14): DC/DC Converter (Battery) Side Gate
Drive Pin. This pin provides gate drive to the external
MOSFET (BAT-FET) that connects to V BAT via the trans-
former.
occurs.
1980f
6
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1980EGN | IC PWM BATT CHARGER/CONV 24-SSOP |
| PCG0J181MCL1GS | CAP ALUM 180UF 6.3V 20% SMD |
| FRN0.50TB | TRACER 1/2" BLACK W/WHITE 500' |
| LTC1980EGN#PBF | IC PWM BATT CHARGER/CONV 24-SSOP |
| DS1233MS-3+ | IC ECONORESET 3.3V(MC33164)8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1981ES5 | 制造商:Linear Technology 功能描述:MOSFET DRVR 1-OUT Hi Side 5-Pin TSOT-23 |
| LTC1981ES5#PBF | 制造商:Linear Technology 功能描述:MOSFET DRVR 1-OUT Hi Side 5-Pin TSOT-23 制造商:Linear Technology 功能描述:DP-Power Controller, CUT TAPE Single Micropower Hi Side Sw Controller 制造商:Linear Technology 功能描述:DRIVER, MOSFET, HIGH/LOW SIDE, SOT-23, Device Type:MOSFET, Module Configuration:High Side, Low Side, Supply Voltage Min:1.8V, Supply Voltage Max:5.5V, Driver Case Style:SOT-23, No. of Pins:5, Operating Temperature Min:-40C , RoHS Compliant: Yes |
| LTC1981ES5#TR | 功能描述:IC HI-SIDE SW CTRL SNGL TSOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:低端 输入类型:非反相 延迟时间:40ns 电流 - 峰:9A 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:- 电源电压:4.5 V ~ 35 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263 包装:管件 |
| LTC1981ES5#TRM | 功能描述:IC HI-SIDE SW CTRL SNGL TSOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
| LTC1981ES5#TRMPBF | 功能描述:IC HI-SIDE SW CTRL SNGL TSOT23-5 RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:95 系列:- 配置:高端和低端，独立 输入类型:非反相 延迟时间:160ns 电流 - 峰:290mA 配置数:1 输出数:2 高端电压 - 最大（自引导启动）:600V 电源电压:10 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 产品目录页面:1381 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。