- 您现在的位置：买卖IC网 > PDF目录14185 > LTC1983ES6-3#TR (Linear Technology)IC REG SWITCHD CAP INV -3V SOT23 PDF资料下载
参数资料
| 型号： | LTC1983ES6-3#TR |
| 厂商： | Linear Technology |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC REG SWITCHD CAP INV -3V SOT23 |
| 标准包装： | 2,500 |
| 类型： | 切换式电容器（充电泵），反相 |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | -3V |
| 输入电压： | 2.3 V ~ 5.5 V |
| PWM 型： | Burst Mode? |
| 频率 - 开关： | 900kHz |
| 电流 - 输出： | 100mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 细型，TSOT-23-6 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | TSOT-23-6 |
| 其它名称： | LTC1983ES6-3TR LTC1983ES63TR |
LTC1983-3/LTC1983-5
OPERATIO
(Refer to Block Diagram)
V OUT
Inrush Currents
During normal operation, V IN will experience current tran-
sients in the several hundred milliamp range whenever the
charge pump is enabled. During start-up, these inrush
currents may approach 1 to 2 amps. For this reason, it is
V IN
C IN
10 μ F
TANTALUM
3.3V TO 5.5V
LTC1983-3
V IN SHDN
GND
C + C –
FROM MPU
SHDN
–3V ± 4%
C OUT
10 μ F
CERAMIC
important to minimize the source resistance between the
input supply and the V IN pin. Too much source resistance
may result in regulation problems or even prevent start-
up. One way that this can be avoided (especially when the
source impedance can’t be lowered due to system con-
straints) is to use a large V IN capacitor with low ESR right
C FLY
1 μ F
CERAMIC
SHDN PIN WAVEFORMS:
at the V IN pin. If ceramic capacitors are used, you may
need to add 1 μ F to 10 μ F tantalum capacitor in parallel to
LOW I Q MODE
(I OUT ≤ 100 μ A)
V OUT LOAD ENABLE MODE
(I OUT = 100 μ A TO 100mA)
limit input voltage transients. Input voltage transients will
occur if V IN is applied via a switch or a plug. One example
(1Hz TO 100Hz, 2% TO 5% DUTY CYCLE)
1983 F02
of this situation is in USB applications.
Ultralow Quiescent Current Regulated Supply
The LTC1983 contains an internal resistor divider (refer to
the Block Diagram) that draws only 1 μ A (typ for the 3V
version) from V OUT during normal operation. During shut-
down, the resistor divider is disconnected from the output
and the part draws only leakage current from the output.
During no-load conditions, applying a 1Hz to 100Hz, 2%
to 5% duty cycle signal to the SHDN pin ensures that the
circuit of Figure 2 comes out of shutdown frequently
enough to maintain regulation even under low-load condi-
tions. Since the part spends nearly all of its time in
shutdown, the no-load quiescent current is essentially
zero. However, the part will still be in operation during the
time the SHDN pin is high, so the current will not be zero
and can be calculated using the following equations to
determine the approximate maximum current: I IN(MAX) =
[(Time out of shutdown) ? (Burst Mode operation quies-
cent current) + (Normal operating I IN ) ? (Time output is
being charged before the LTC1983 enters Burst Mode
operation)]/(Period of SHDN signal). This number will be
highly dependent on the amount of board leakage current
and how many devices are connected to V OUT (each will
draw some leakage current) and must be calculated and
verified for each different board design.
Figure 2. Ultralow Quiescent Current Regulated Supply
The LTC1983 must be out of shutdown for a minimum
duration of 200 μ s to allow enough time to sense the output
and keep it in regulation. A 1Hz, 2% duty cycle signal will
keep V OUT in regulation under no-load conditions. Even
though the term no-load is used, there will always be board
leakage current and leakage current drawn by anything
connected to V OUT . This is why it is necessary to wake the
part up every once in a while to verify regulation. As the
V OUT load current increases, the frequency with which the
part is taken out of shutdown must also be increased to
prevent V OUT from drooping below the – 2.88V (for the 3V
version) during the OFF phase (see Figure 3). A 100Hz, 2%
duty cycle signal on the SHDN pin ensures proper regula-
tion with load currents as high as 100 μ A. When load
current greater than 100 μ A is needed, the SHDN pin must
be forced high as in normal operation.
Each time the LTC1983 comes out of shutdown, the part
delivers a minimum of one clock cycle worth of charge to
the output. Under high V IN (>4V) and/or low I OUT (<10 μ A)
conditions, this behavior may cause a net excess of charge
to be delivered to the output capacitor if a high frequency
signal is used on the SHDN pin (e.g., 50Hz to 100Hz).
Under such conditions, V OUT will slowly drift positive and
may even go out of regulation. To avoid this potential
1983fa
8
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6865UK45D6L+T | IC MPU SUPERVISOR SOT23-5 |
| MAX6865UK45D5S+T | IC MPU SUPERVISOR SOT23-5 |
| VI-J7M-CZ-F3 | CONVERTER MOD DC/DC 10V 25W |
| CGS224U016X4C | CAP ALUM 220000UF 16V SCREW |
| MAX6865UK45D5L+T | IC MPU SUPERVISOR SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1983ES6-5#PBF | 制造商:Linear Technology 功能描述:IC INVERTING CHARGE PUMP CONV 6-SOT-23 制造商:Linear Technology 功能描述:IC, INVERTING CHARGE PUMP CONV, 6-SOT-23 制造商:Linear Technology 功能描述:IC, INVERTING CHARGE PUMP CONV, 6-SOT-23; Primary Input Voltage:5V; No. of Outputs:1; Output Voltage:-5V; Output Current:100mA; No. of Pins:6; Operating Temperature Min:-40C; Operating Temperature Max:85C; MSL:MSL 1 - Unlimited ;RoHS Compliant: Yes |
| LTC1983ES6-5#TR | 功能描述:IC REG SWITCHD CAP INV -5V SOT23 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:500 系列:- 类型:切换式电容器（充电泵），反相 输出类型:固定 输出数:1 输出电压:-3V 输入电压:2.3 V ~ 5.5 V PWM 型:Burst Mode? 频率 - 开关:900kHz 电流 - 输出:100mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 包装:带卷 (TR) 供应商设备封装:TSOT-23-6 其它名称:LTC1983ES6-3#TRMTR |
| LTC1983ES6-5#TRM | 功能描述:IC REG SWITCHD CAP INV -5V SOT23 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC1983ES6-5#TRMPBF | 功能描述:IC REG SWITCHD CAP INV -5V SOT23 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:High Efficiency Current Mode Switching Regulators CMOS LDO Regulators 特色产品:BD91x Series Step-Down Regulators 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:2 输出电压:3.3V，0.8 V ~ 2.5 V 输入电压:4.5 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:1MHz 电流 - 输出:1.5A 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 包装:带卷 (TR) 供应商设备封装:VQFN020V4040 产品目录页面:1373 (CN2011-ZH PDF) 其它名称:BD9152MUV-E2TR |
| LTC1983ES6-5#TRPBF | 功能描述:IC REG SWITCHD CAP INV -5V SOT23 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:500 系列:- 类型:切换式电容器（充电泵），反相 输出类型:固定 输出数:1 输出电压:-3V 输入电压:2.3 V ~ 5.5 V PWM 型:Burst Mode? 频率 - 开关:900kHz 电流 - 输出:100mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 包装:带卷 (TR) 供应商设备封装:TSOT-23-6 其它名称:LTC1983ES6-3#TRMTR |
发布紧急采购，3分钟左右您将得到回复。