- 您现在的位置：买卖IC网 > PDF目录39410 > LTC2140IUP-14#PBF (LINEAR TECHNOLOGY CORP) 2-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC64 PDF资料下载
参数资料
| 型号： | LTC2140IUP-14#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | ADC |
| 英文描述： | 2-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC64 |
| 封装： | 9 X 9 MM, LEAD FREE, PLASTIC, MO-220WNJR-5, QFN-64 |
| 文件页数： | 8/36页 |
| 文件大小： | 528K |
| 代理商： | LTC2140IUP-14#PBF |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC2142-14/
LTC2141-14/LTC2140-14
16
21421014f
PINS THAT ARE THE SAME FOR ALL DIGITAL
OUTPUT MODES
VDD (Pins 1, 16, 17, 64): Analog Power Supply, 1.7V to
1.9V. Bypass to ground with 0.1μF ceramic capacitors.
Adjacent pins can share a bypass capacitor.
VCM1 (Pin 2):Common Mode Bias Output, Nominally Equal
to VDD/2. VCM1 should be used to bias the common mode
of the analog inputs to channel 1. Bypass to ground with
a 0.1μF ceramic capacitor.
GND (Pins 3, 6, 14): ADC Power Ground.
AIN1+ (Pin 4): Channel 1 Positive Differential Analog
Input.
AIN1– (Pin 5): Channel 1 Negative Differential Analog
Input.
REFH (Pins 7, 9): ADC High Reference. See the Applica-
tions Information section for recommended bypassing
circuits for REFH and REFL.
REFL (Pins 8, 10): ADC Low Reference. See the Applica-
tions Information section for recommended bypassing
circuits for REFH and REFL.
PAR/SER (Pin 11): Programming Mode Selection Pin. Con-
nect to ground to enable the serial programming mode. CS,
SCK, SDI, SDO become a serial interface that control the
A/D operating modes. Connect to VDD to enable the parallel
programming mode where CS, SCK, SDI, SDO become
parallel logic inputs that control a reduced set of the A/D
operating modes. PAR/SER should be connected directly
to ground or VDD and not be driven by a logic signal.
AIN2+ (Pin 12): Channel 2 Positive Differential Analog
Input.
AIN2– (Pin 13): Channel 2 Negative Differential Analog
Input.
VCM2 (Pin 15): Common Mode Bias Output, Nominally
Equal to VDD/2. VCM2 should be used to bias the common
mode of the analog inputs to channel 2. Bypass to ground
with a 0.1μF ceramic capacitor.
ENC+ (Pin 18): Encode Input. Conversion starts on the
rising edge.
ENC– (Pin 19):
Encode Complement Input. Conversion
starts on the falling edge. Tie to GND for single-ended
encode mode.
CS (Pin 20): In Serial Programming Mode, (PAR/SER =
0V), CS Is the Serial Interface Chip Select Input. When
CS is low, SCK is enabled for shifting data on SDI into
the mode control registers. In the parallel programming
mode (PAR/SER = VDD), CS controls the clock duty cycle
stabilizer (see Table 2). CS can be driven with 1.8V to
3.3V logic.
SCK (Pin 21): In Serial Programming Mode, (PAR/SER =
0V), SCK Is the Serial Interface Clock Input. In the parallel
programming mode (PAR/SER = VDD), SCK controls the
digital output mode (see Table 2). SCK can be driven with
1.8V to 3.3V logic.
SDI (Pin 22): In Serial Programming Mode, (PAR/SER =
0V), SDI Is the Serial Interface Data Input. Data on SDI is
clocked into the mode control registers on the rising edge
of SCK. In the parallel programming mode (PAR/SER =
VDD), SDI can be used together with SDO to power down
the part (see Table 2). SDI can be driven with 1.8V to
3.3V logic.
OGND (Pin 41): Output Driver Ground. Must be shorted
to the ground plane by a very low inductance path. Use
multiple vias close to the pin.
OVDD (Pin 42): Output Driver Supply. Bypass to ground
with a 0.1μF ceramic capacitor.
SDO (Pin 61): In Serial Programming Mode, (PAR/SER
= 0V), SDO Is the Optional Serial Interface Data Output.
Data on SDO is read back from the mode control regis-
ters and can be latched on the falling edge of SCK. SDO
is an open-drain NMOS output that requires an external
2k pull-up resistor to 1.8V – 3.3V. If read back from the
mode control registers is not needed, the pull-up resistor
is not necessary and SDO can be left unconnected. In the
parallel programming mode (PAR/SER = VDD), SDO can
be used together with SDI to power down the part (see
Table 2). When used as an input, SDO can be driven with
1.8V to 3.3V logic through a 1k series resistor.
VREF (Pin 62): Reference Voltage Output. Bypass to
ground with a 2.2μF ceramic capacitor. The output voltage
is nominally 1.25V.
PIN FUNCTIONS
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2140CUP-14#TRPBF | 2-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC64 |
| LTC2141IUP-14#TRPBF | 2-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC64 |
| LTC2141CUP-14#TRPBF | 2-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC64 |
| LTC2143CUP-14#TRPBF | 2-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC64 |
| LTC2143IUP-14#PBF | 2-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2141-14 | 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit, 65Msps/ 40Msps/25Msps Low Power Dual ADCs |
| LTC2141CUP-12#PBF | 功能描述:IC ADC DUAL 12BIT 40MSPS 64-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC2141CUP-12#TRPBF | 功能描述:IC ADC DUAL 12BIT 40MSPS 64-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC2141CUP-14#PBF | 功能描述:IC ADC DUAL 14BIT 40 MSPS 64-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| LTC2141CUP-14#TRPBF | 功能描述:IC ADC DUAL 14BIT 40 MSPS 64-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。