- 您现在的位置：买卖IC网 > PDF目录10652 > LTC2172IUKG-14#PBF (Linear Technology)IC ADC 14BIT SER/PAR 65M 52-QFN PDF资料下载
参数资料
| 型号： | LTC2172IUKG-14#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/34页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT SER/PAR 65M 52-QFN |
| 标准包装： | 45 |
| 位数： | 14 |
| 采样率（每秒）： | 65M |
| 数据接口： | Serial LVDS |
| 转换器数目： | 4 |
| 功率耗散（最大）： | 419mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 52-WFQFN 裸露焊盘 |
| 供应商设备封装： | 52-QFN（7x8） |
| 包装： | 管件 |
| 输入数目和类型： | 2 Differential; 2 Single-Ended |
| 配用： | DC1371A-ND - BOARD USB DATA ACQUISITION HS |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LTC2172-14/
LTC2171-14/LTC2170-14
17
21721014fb
AIN1+ (Pin 1): Channel 1 Positive Differential Analog
Input.
AIN1– (Pin 2): Channel 1 Negative Differential Analog
Input.
VCM12 (Pin 3): Common Mode Bias Output, Nominally
Equal to VDD/2. VCM should be used to bias the common
mode of the analog inputs of channels 1 and 2. Bypass
to ground with a 0.1F ceramic capacitor.
AIN2+ (Pin 4): Channel 2 Positive Differential Analog
Input.
AIN2– (Pin 5): Channel 2 Negative Differential Analog
Input.
REFH (Pins 6, 7): ADC High Reference. Bypass to Pin 8
and Pin 9 with a 2.2F ceramic capacitor, and to ground
with a 0.1F ceramic capacitor.
REFL (Pins 8, 9): ADC Low Reference. Bypass to Pin 6
and Pin 7 with a 2.2F ceramic capacitor, and to ground
with a 0.1F ceramic capacitor.
AIN3+ (Pin 10): Channel 3 Positive Differential Analog
Input.
AIN3– (Pin 11): Channel 3 Negative Differential Analog
Input.
VCM34 (Pin 12): Common Mode Bias Output, Nominally
Equal to VDD/2. VCM should be used to bias the common
mode of the analog inputs of channels 3 and 4. Bypass
to ground with a 0.1F ceramic capacitor.
AIN4+ (Pin 13): Channel 4 Positive Differential Analog
Input.
AIN4– (Pin 14): Channel 4 Negative Differential Analog
Input.
VDD (Pins 15, 16, 51, 52): 1.8V Analog Power Supply.
Bypass to ground with 0.1F ceramic capacitors. Adjacent
pins can share a bypass capacitor.
ENC+ (Pin 17): Encode Input. Conversion starts on the
rising edge.
ENC– (Pin 18): Encode Complement Input. Conversion
starts on the falling edge.
CS(Pin19):Inserialprogrammingmode(PAR/SER=0V),
CS is the serial interface chip select input. When CS is low,
SCK is enabled for shifting data on SDI into the mode
controlregisters.Inparallelprogrammingmode(PAR/SER
= VDD), CS selects two-lane or one-lane output mode. CS
can be driven with 1.8V to 3.3V logic.
SCK (Pin 20): In serial programming mode (PAR/SER
= 0V), SCK is the serial interface clock input. In parallel
programming mode (PAR/SER = VDD),SCKselects3.5mA
or 1.75mA LVDS output currents. SCK can be driven with
1.8V to 3.3V logic.
SDI (Pin 21): In serial programming mode (PAR/SER =
0V), SDI is the serial interface data input. Data on SDI
is clocked into the mode control registers on the rising
edge of SCK. In parallel programming mode (PAR/SER =
VDD), SDI can be used to power down the part. SDI can
be driven with 1.8V to 3.3V logic.
GND (Pins 22, 45, 49, Exposed Pad Pin 53): ADC Power
Ground. The exposed pad must be soldered to the PCB
ground.
OGND (Pin 33): Output Driver Ground. Must be shorted
to the ground plane by a very low inductance path. Use
multiple vias close to the pin.
OVDD (Pin 34): Output Driver Supply. Bypass to ground
with a 0.1F ceramic capacitor.
SDO (Pin 46): In serial programming mode (PAR/SER
= 0V), SDO is the optional serial interface data output.
Data on SDO is read back from the mode control registers
and can be latched on the falling edge of SCK. SDO is
an open-drain N-channel MOSFET output that requires
an external 2k pull-up resistor of 1.8V to 3.3V. If read-
back from the mode control registers is not needed,
the pull-up resistor is not necessary and SDO can be
left unconnected. In parallel programming mode (PAR/
SER = VDD), SDO is an input that enables internal 100
termination resistors on the digital outputs. When used
as an input, SDO can be driven with 1.8V to 3.3V logic
through a 1k series resistor.
pin FuncTions
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JTN-MY-F4 | CONVERTER MOD DC/DC 18.5V 50W |
| MAX970EEE+T | IC COMPARATOR R-R 16-QSOP |
| MAX490CSA+ | IC TXRX RS485/RS422 LOWPWR 8SOIC |
| LTC2261IUJ-14#PBF | IC ADC 14-BIT 125MSPS 40-QFN |
| MAX970EEE-T | IC COMPARATR QUAD R-R I/O 16QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2172IUKG-14TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:14-Bit, 65Msps/40Msps/25Msps Low Power Quad ADCs |
| LTC2173-12 | 制造商:LINER 制造商全称:Linear Technology 功能描述:14-Bit, 125Msps/105Msps/ 80Msps Low Power Octal ADCs |
| LTC2173-14 | 制造商:LINER 制造商全称:Linear Technology 功能描述:14-Bit, 125Msps/105Msps/ 80Msps Low Power Octal ADCs |
| LTC2173CUKG-12#PBF | 功能描述:IC ADC 12BIT SER 80MSPS 52-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| LTC2173CUKG-12#TRPBF | 功能描述:IC ADC 12BIT 80MSPS QUAD 52QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。