- 您现在的位置：买卖IC网 > PDF目录10254 > LTC2226CUH#PBF (Linear Technology)IC ADC 12BIT 25MSPS SAMPL 32-QFN PDF资料下载
参数资料
| 型号： | LTC2226CUH#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 25MSPS SAMPL 32-QFN |
| 标准包装： | 73 |
| 位数： | 12 |
| 采样率（每秒）： | 25M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 90mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 管件 |
| 输入数目和类型： | 1 个单端，双极; 1 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC2228/LTC2227/LTC2226
17
222876fb
APPLICATIONS INFORMATION
Single-Ended Input
For cost-sensitive applications, the analog inputs can be
driven single ended. With a single-ended input the har-
monic distortion and INL will degrade, but the SNR and
DNL will remain unchanged. For a single-ended input, AIN+
should be driven with the input signal and AIN– should be
connected to 1.5V or VCM.
Common Mode Bias
For optimal performance the analog inputs should be driven
differentially. Each input should swing ±0.5V for the 2V
range or ±0.25V for the 1V range, around a common mode
voltage of 1.5V. The VCM output pin (Pin 31) may be used
to provide the common mode bias level. VCM can be tied
directly to the center tap of a transformer to set the DC
input level or as a reference level to an op amp differential
driver circuit. The VCM pin must be bypassed to ground
close to the ADC with a 2.2μF or greater capacitor.
Input Drive Impedance
As with all high performance, high speed ADCs, the dy-
namic performance of the LTC2228/LTC2227/LTC2226 can
be inuenced by the input drive circuitry, particularly the
second and third harmonics. Source impedance and input
reactance can inuence SFDR. At the falling edge of CLK,
the sample-and-hold circuit will connect the 4pF sampling
capacitor to the input pin and start the sampling period.
The sampling period ends when CLK rises, holding the
sampled input on the sampling capacitor. Ideally the input
circuitry should be fast enough to fully charge the sam-
pling capacitor during the sampling period 1/(2FENCODE);
however, this is not always possible and the incomplete
settling may degrade the SFDR. The sampling glitch has
been designed to be as linear as possible to minimize the
effects of incomplete settling.
For the best performance, it is recommended to have a
source impedance of 100Ω or less for each input. The
source impedance should be matched for the differential
inputs. Poor matching will result in higher even order
harmonics, especially the second.
Input Drive Circuits
Figure 3 shows the LTC2228/LTC2227/LTC2226 being
driven by an RF transformer with a center tapped sec-
ondary. The secondary center tap is DC biased with VCM,
setting the ADC input signal at its optimum DC level.
Terminating on the transformer secondary is desirable,
as this provides a common mode path for charging
glitches caused by the sample and hold. Figure 3 shows
a 1:1 turns ratio transformer. Other turns ratios can be
used if the source impedance seen by the ADC does not
exceed 100Ω for each ADC input. A disadvantage of us-
ing a transformer is the loss of low frequency response.
Most small RF transformers have poor performance at
frequencies below 1MHz.
Figure 4 demonstrates the use of a differential amplier to
convert a single-ended input signal into a differential input
signal. The advantage of this method is that it provides
low frequency input response; however, the limited gain
bandwidth of most op amps will limit the SFDR at high
input frequencies.
25Ω
0.1μF
AIN
+
AIN
–
12pF
2.2μF
VCM
LTC2228/27/26
ANALOG
INPUT
0.1μF
T1
1:1
T1 = MA/COM ETC1-1T
RESISTORS, CAPACITORS
ARE 0402 PACKAGE SIZE
222876 F03
Figure 3. Single-Ended to Differential Conversion Using a Transformer
相关PDF资料 |
PDF描述 |
|---|---|
| AD7264BCPZ-5 | IC ADC 14BIT 2CH 500KSPS 48LFCSP |
| VI-23W-CU-F1 | CONVERTER MOD DC/DC 5.5V 200W |
| VE-22T-MX-F2 | CONVERTER MOD DC/DC 6.5V 75W |
| VI-23V-IW-S | CONVERTER MOD DC/DC 5.8V 100W |
| VE-22R-MX-F4 | CONVERTER MOD DC/DC 7.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2226CUH-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit, 65/40/25Msps Low Power 3V ADCs |
| LTC2226CUH-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit, 65/40/25Msps Low Power 3V ADCs |
| LTC2226H | 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit, 25Msps 125°C ADC in LQFP |
| LTC2226HLU#PBF | 功能描述:IC ADC 12BIT 25MSPS 32-TQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| LTC2226HLU#TRPBF | 制造商:Linear Technology 功能描述:ADC Single Pipelined 25Msps 12-bit Parallel 48-Pin LQFP T/R |
发布紧急采购，3分钟左右您将得到回复。