- 您现在的位置：买卖IC网 > PDF目录10524 > LTC2234IUK#PBF (Linear Technology)IC ADC 10BIT 135MSPS SAMPL 48QFN PDF资料下载
参数资料
| 型号： | LTC2234IUK#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 135MSPS SAMPL 48QFN |
| 标准包装： | 52 |
| 位数： | 10 |
| 采样率（每秒）： | 135M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 680mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN-EP（7x7） |
| 包装： | 管件 |
| 输入数目和类型： | 1 个单端，双极; 1 个差分，双极 |
| 产品目录页面： | 1349 (CN2011-ZH PDF) |
LTC2234
17
2234fa
APPLICATIO S I FOR ATIO
WU
UU
VDD
LTC2234
2234 F11
VDD
ENC–
ENC+
1.6V BIAS
1:4
0.1
F
CLOCK
INPUT
50
6k
TO INTERNAL
ADC CIRCUITS
Figure 11. Transformer Driven ENC+/ENC–
Input Range
The input range can be set based on the application. The
2V input range will provide the best signal-to-noise perfor-
mance while maintaining excellent SFDR. The 1V input
range will have better SFDR performance, but the SNR will
degrade by 1.7dB. See the Typical Performance Charac-
teristics section.
Driving the Encode Inputs
The noise performance of the LTC2234 can depend on the
encode signal quality as much as on the analog input. The
ENC+/ENC– inputs are intended to be driven differentially,
primarily for noise immunity from common mode noise
sources. Each input is biased through a 6k resistor to a
1.6V bias. The bias resistors set the DC operating point for
transformer coupled drive circuits and can set the logic
threshold for single-ended drive circuits.
Any noise present on the encode signal will result in
additional aperture jitter that will be RMS summed with the
inherent ADC aperture jitter.
In applications where jitter is critical (high input frequen-
cies) take the following into consideration:
1. Differential drive should be used.
2. Use as large an amplitude as possible; if transformer
coupled use a higher turns ratio to increase the amplitude.
3. If the ADC is clocked with a sinusoidal signal, filter the
encode signal to reduce wideband noise.
4. Balance the capacitance and series resistance at both
encode inputs so that any coupled noise will appear at both
inputs as common mode noise. The encode inputs have a
common mode range of 1.1V to 2.5V. Each input may be
driven from ground to VDD for single-ended drive.
Maximum and Minimum Encode Rates
The maximum encode rate for the LTC2234 is 135Msps.
For the ADC to operate properly, the encode signal should
have a 50% (
±5%) duty cycle. Each half cycle must have
at least 3.5ns for the ADC internal circuitry to have enough
settling time for proper operation. Achieving a precise
50% duty cycle is easy with differential sinusoidal drive
using a transformer or using symmetric differential logic
such as PECL or LVDS.
An optional clock duty cycle stabilizer circuit can be used
if the input clock has a non 50% duty cycle. This circuit
uses the rising edge of the ENC+ pin to sample the analog
input. The falling edge of ENC+ is ignored and the internal
falling edge is generated by a phase-locked loop. The input
clock duty cycle can vary from 30% to 70% and the clock
duty cycle stabilizer will maintain a constant 50% internal
duty cycle. If the clock is turned off for a long period of
time, the duty cycle stabilizer circuit will require one
hundred clock cycles for the PLL to lock onto the input
clock. To use the clock duty cycle stabilizer, the MODE pin
should be connected to 1/3VDD or 2/3VDD using external
resistors.
The lower limit of the LTC2234 sample rate is determined
by droop of the sample-and-hold circuits. The pipelined
architecture of this ADC relies on storing analog signals on
small valued capacitors. Junction leakage will discharge
the capacitors. The specified minimum operating fre-
quency for the LTC2234 is 1Msps.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2T1-IW-F2 | CONVERTER MOD DC/DC 12V 100W |
| VE-25N-IW-F4 | CONVERTER MOD DC/DC 18.5V 100W |
| AD9649BCPZ-65 | IC ADC 14BIT 65MSPS 32LFCSP |
| AMIS41682CANM1G | TRANSCEIVER CAN 3.3V DGTL 14SOIC |
| AD7723BSZ | IC ADC 16BIT SIGMA-DELTA 44MQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2234UK | 制造商:LINER 制造商全称:Linear Technology 功能描述:10-Bit, 135Msps ADC |
| LTC2236 | 制造商:LINER 制造商全称:Linear Technology 功能描述:14-Bit, 80Msps Low Power 3V ADC |
| LTC2236CUH | 制造商:LINER 制造商全称:Linear Technology 功能描述:10-Bit, 65/40/25Msps Low Noise 3V ADCs |
| LTC2236CUH#PBF | 功能描述:IC ADC 10-BIT 25MSPS 3V 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2236CUH#TRPBF | 功能描述:IC ADC 10BIT 25MSPS 3V 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
发布紧急采购，3分钟左右您将得到回复。