- 您现在的位置：买卖IC网 > PDF目录10307 > LTC2237CUH#TRPBF (Linear Technology)IC ADC 10BIT 40MSPS 3V 32-QFN PDF资料下载
参数资料
| 型号： | LTC2237CUH#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 40MSPS 3V 32-QFN |
| 标准包装： | 2,500 |
| 位数： | 10 |
| 采样率（每秒）： | 40M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 144mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个单端，双极; 1 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC2238/LTC2237/LTC2236
22
223876fa
APPLICATIO S I FOR ATIO
WU
UU
Heat Transfer
Most of the heat generated by the LTC2238/LTC2237/
LTC2236 is transferred from the die through the bottom-
side exposed pad and package leads onto the printed
circuit board. For good electrical and thermal perfor-
mance, the exposed pad should be soldered to a large
grounded pad on the PC board. It is critical that all ground
pins are connected to a ground plane of sufficient area.
Clock Sources for Undersampling
Undersampling raises the bar on the clock source and the
higher the input frequency, the greater the sensitivity to
clock jitter or phase noise. A clock source that degrades
SNR of a full-scale signal by 1dB at 70MHz will degrade
SNR by 3dB at 140MHz, and 4.5dB at 190MHz.
In cases where absolute clock frequency accuracy is
relatively unimportant and only a single ADC is required, a
3V canned oscillator from vendors such as Saronix or
Vectron can be placed close to the ADC and simply
connected directly to the ADC. If there is any distance to the
ADC, some source termination to reduce ringing that may
occur even over a fraction of an inch is advisable. You must
not allow the clock to overshoot the supplies or perfor-
mance will suffer. Do not filter the clock signal with a
narrow band filter unless you have a sinusoidal clock
source, as the rise and fall time artifacts present in typical
digital clock signals will be translated into phase noise.
The lowest phase noise oscillators have single-ended
sinusoidal outputs, and for these devices the use of a filter
close to the ADC may be beneficial. This filter should be
close to the ADC to both reduce roundtrip reflection times,
as well as reduce the susceptibility of the traces between
the filter and the ADC. If you are sensitive to close-in phase
noise, the power supply for oscillators and any buffers
must be very stable, or propagation delay variation with
supply will translate into phase noise. Even though these
clock sources may be regarded as digital devices, do not
operate them on a digital supply. If your clock is also used
to drive digital devices such as an FPGA, you should locate
the oscillator, and any clock fan-out devices close to the
ADC, and give the routing to the ADC precedence. The
clock signals to the FPGA should have series termination
at the source to prevent high frequency noise from the
FPGA disturbing the substrate of the clock fan-out device.
If you use an FPGA as a programmable divider, you must
re-time the signal using the original oscillator, and the re-
timing flip-flop as well as the oscillator should be close to
the ADC, and powered with a very quiet supply.
For cases where there are multiple ADCs, or where the
clock source originates some distance away, differential
clock distribution is advisable. This is advisable both from
the perspective of EMI, but also to avoid receiving noise
from digital sources both radiated, as well as propagated
in the waveguides that exist between the layers of multi-
layer PCBs.
The differential pairs must be close together, and dis-
tanced from other signals. The differential pair should be
guarded on both sides with copper distanced at least 3x
the distance between the traces, and grounded with vias
no more than 1/4 inch apart.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2N4-CU-S | CONVERTER MOD DC/DC 48V 200W |
| MS27484T24F29PLC | CONN HSG PLUG 29POS STRGHT PINS |
| VI-2N0-CU-S | CONVERTER MOD DC/DC 5V 200W |
| VE-BNX-IX-B1 | CONVERTER MOD DC/DC 5.2V 75W |
| MS27505E11F98SA | CONN RCPT 6POS BOX MNT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2237IUH | 制造商:Linear Technology 功能描述:ADC Single Pipelined 40Msps 10-bit Parallel 32-Pin QFN EP |
| LTC2237IUH#PBF | 功能描述:IC ADC 10-BIT 40MSPS 3V 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| LTC2237IUH#TRPBF | 功能描述:IC ADC 10BIT 40MSPS 3V 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| LTC2238 | 制造商:LINER 制造商全称:Linear Technology 功能描述:14-Bit, 80Msps Low Power 3V ADC |
| LTC2238CUH | 制造商:Linear Technology 功能描述:ADC Single Pipelined 65Msps 10-bit Parallel 32-Pin QFN EP |
发布紧急采购，3分钟左右您将得到回复。