参数资料
型号: LTC2247CUH#PBF
厂商: Linear Technology
文件页数: 11/24页
文件大小: 0K
描述: IC ADC 14BIT 40MSPS SAMPL 32-QFN
标准包装: 73
位数: 14
采样率(每秒): 40M
数据接口: 并联
转换器数目: 1
功率耗散(最大): 144mW
电压电源: 单电源
工作温度: 0°C ~ 70°C
安装类型: 表面贴装
封装/外壳: 32-WFQFN 裸露焊盘
供应商设备封装: 32-QFN 裸露焊盘(5x5)
包装: 管件
输入数目和类型: 1 个单端,双极; 1 个差分,双极
LTC2248/LTC2247/LTC2246
19
224876fa
APPLICATIO S I FOR ATIO
WU
UU
As with all high speed/high resolution converters, the
digital output loading can affect the performance. The
digital outputs of the LTC2248/LTC2247/LTC2246 should
drive a minimal capacitive load to avoid possible interac-
tion between the digital outputs and sensitive input cir-
cuitry. The output should be buffered with a device such as
an ALVCH16373 CMOS latch. For full speed operation the
capacitive load should be kept under 10pF.
Lower OVDD voltages will also help reduce interference
from the digital outputs.
Data Format
Using the MODE pin, the LTC2248/LTC2247/LTC2246
parallel digital output can be selected for offset binary or
2’s complement format. Connecting MODE to GND or
1/3VDD selects offset binary output format. Connecting
MODE to 2/3VDD or VDD selects 2’s complement output
format. An external resistor divider can be used to set the
1/3VDD or 2/3VDD logic values. Table 2 shows the logic
states for the MODE pin.
Output Driver Power
Separate output power and ground pins allow the output
drivers to be isolated from the analog circuitry. The power
supply for the digital output buffers, OVDD, should be tied
to the same power supply as for the logic being driven. For
example if the converter is driving a DSP powered by a 1.8V
supply, then OVDD should be tied to that same 1.8V supply.
OVDD can be powered with any voltage from 500mV up to
3.6V. OGND can be powered with any voltage from GND up
to 1V and must be less than OVDD. The logic outputs will
swing between OGND and OVDD.
Output Enable
The outputs may be disabled with the output enable pin, OE.
OE high disables all data outputs including OF. The data ac-
cess and bus relinquish times are too slow to allow the
outputs to be enabled and disabled during full speed op-
eration. The output Hi-Z state is intended for use during long
periods of inactivity.
Sleep and Nap Modes
The converter may be placed in shutdown or nap modes
to conserve power. Connecting SHDN to GND results in
normal operation. Connecting SHDN to VDD and OE to VDD
results in sleep mode, which powers down all circuitry
including the reference and typically dissipates 1mW. When
exiting sleep mode it will take milliseconds for the output
data to become valid because the reference capacitors have
to recharge and stabilize. Connecting SHDN to VDD and OE
to GND results in nap mode, which typically dissipates
15mW. In nap mode, the on-chip reference circuit is kept
on, so that recovery from nap mode is faster than that from
sleep mode, typically taking 100 clock cycles. In both sleep
and nap modes, all digital outputs are disabled and enter
the Hi-Z state.
Table 2. MODE Pin Function
Clock Duty
MODE Pin
Output Format
Cycle Stablizer
0
Offset Binary
Off
1/3VDD
Offset Binary
On
2/3VDD
2’s Complement
On
VDD
2’s Complement
Off
Overflow Bit
When OF outputs a logic high the converter is either
overranged or underranged.
相关PDF资料
PDF描述
MAX9203ESA+T IC COMPARATOR LP 8-SOIC
VE-B1W-IV-F1 CONVERTER MOD DC/DC 5.5V 150W
MAX9107ESA+T IC COMPAR LP DUAL 8-SOIC
AD7691BRMZ IC ADC 18BIT SAR 250KSPS 10-MSOP
VE-B1V-IV-F4 CONVERTER MOD DC/DC 5.8V 150W
相关代理商/技术参数
参数描述
LTC2247IUH 制造商:Linear Technology 功能描述:ADC Single Pipelined 40Msps 14-bit Parallel 32-Pin QFN EP
LTC2247IUH#PBF 功能描述:IC ADC 14BIT 40MSPS SAMPL 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率(每秒):1M 数据接口:串行,SPI? 转换器数目:1 功率耗散(最大):- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘(4x4) 包装:Digi-Reel® 输入数目和类型:8 个单端,单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6
LTC2247IUH#TR 制造商:Linear Technology 功能描述:ADC Single Pipelined 40Msps 14-bit Parallel 32-Pin QFN EP T/R
LTC2247IUH#TRPBF 功能描述:IC ADC 14BIT 40MSPS SAMPL 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率(每秒):83k 数据接口:串行,并联 转换器数目:1 功率耗散(最大):95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP(0.600",15.24mm) 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端,双极
LTC2248 制造商:LINER 制造商全称:Linear Technology 功能描述:14-Bit, 80Msps Low Power 3V ADC