- 您现在的位置：买卖IC网 > PDF目录10107 > LTC2260CUJ-12#TRPBF (Linear Technology)IC ADC 12BIT 105MSPS 40-QFN PDF资料下载
参数资料
| 型号： | LTC2260CUJ-12#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 18/34页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 105MSPS 40-QFN |
| 产品培训模块： | LTC2262 - Ultra Low Power High Speed ADCs |
| 标准包装： | 2,000 |
| 位数： | 12 |
| 采样率（每秒）： | 105M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 122mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN（6x6） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个差分 |
| 配用： | DC890B-ND - BOARD USB DATA COLLECTION |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LTC2261-12
LTC2260-12/LTC2259-12
25
226112fc
For more information www.linear.com/LTC2261-12
The digital output is decoded at the receiver by inverting
the odd bits (D1, D3, D5, D7, D9, D11). The alternate
bit polarity mode is independent of the digital output
randomizer—either, both or neither function can be on
at the same time. When alternate bit polarity mode is on,
the data format is offset binary and the 2’s complement
control bit has no effect. The alternate bit polarity mode is
enabledbyseriallyprogrammingmodecontrolregisterA4.
Digital Output Test Patterns
To allow in-circuit testing of the digital interface to the
A/D, there are several test modes that force the A/D data
outputs (OF, D11-D0) to known values:
All 1s: All outputs are 1
All 0s: All outputs are 0
Alternating: Outputs change from all 1s to all 0s on
alternating samples
Checkerboard: Outputs change from 1010101010101
to 0101010101010 on alternating samples
The digital output test patterns are enabled by serially
programming mode control register A4. When enabled,
the test patterns override all other formatting modes: 2’s
complement, randomizer, alternate-bit-polarity.
Output Disable
The digital outputs may be disabled by serially program-
mingmodecontrolregisterA3.Alldigitaloutputsincluding
OFandCLKOUTaredisabled.Thehighimpedancedisabled
state is intended for long periods of inactivity—it is too
slow to multiplex a data bus between multiple converters
at full speed.
Sleep and Nap Modes
The A/D may be placed in sleep or nap modes to conserve
power. In sleep mode the entire A/D converter is powered
down,resultingin0.5mWpowerconsumption.Sleepmode
is enabled by mode control register A1 (serial program-
ming mode), or by SDI (parallel programming mode).
The amount of time required to recover from sleep mode
depends on the size of the bypass capacitors on VREF,
REFH, and REFL. For the suggested values in Figure 8,
the A/D will stabilize after 2ms.
InnapmodetheA/Dcoreispowereddownwhiletheinternal
referencecircuitsstayactive,allowingfasterwake-upthan
from sleep mode. Recovering from nap mode requires at
least 100 clock cycles. If the application demands very
accurate DC settling then an additional 50s should be
allowedsotheon-chipreferencescansettlefromtheslight
temperature shift caused by the change in supply current
as the A/D leaves nap mode. Nap mode is enabled by mode
control register A1 in the serial programming mode.
DEVICE PROGRAMMING MODES
The operating modes of the LTC2261-12 can be pro-
grammed by either a parallel interface or a simple serial
interface. The serial interface has more flexibility and
can program all available modes. The parallel interface
is more limited and can only program some of the more
commonly used modes.
Parallel Programming Mode
To use the parallel programming mode, PAR/SER should
be tied to VDD. The CS, SCK and SDI pins are binary logic
inputs that set certain operating modes. These pins can
be tied to VDD or ground, or driven by 1.8V, 2.5V or 3.3V
CMOS logic. Table 2 shows the modes set by CS, SCK
and SDI.
Table 2. Parallel Programming Mode Control Bits (PAR/SER = VDD)
PIN
DESCRIPTION
CS
Clock Duty Cycle Stabilizer Control Bit
0 = Clock Duty Cycle Stabilizer Off
1 = Clock Duty Cycle Stabilizer On
SCK
Digital Output Mode Control Bit
0 = Full-Rate CMOS Output Mode
1 = Double-Data Rate LVDS Output Mode
(3.5mA LVDS Current, Internal Termination Off)
SDI
Power Down Control Bit
0 = Normal Operation
1 = Sleep Mode
applicaTions inForMaTion
相关PDF资料 |
PDF描述 |
|---|---|
| MS27473E20B16P | CONN PLUG 16POS STRAIGHT W/PINS |
| MS27472T24B61PB | CONN RCPT 61POS WALL MT W/PINS |
| IDT7204L25TPI | IC FIFO ASYNCH 4KX9 25NS 28DIP |
| ADM207EAN | IC TXRX RS232 5DVR/3REC 24DIP |
| IDT7204L25PI | IC FIFO ASYNCH 4KX9 25NS 28DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2260CUJ-14#PBF | 功能描述:IC ADC 14-BIT 105MSPS 40-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC2260CUJ-14#TRPBF | 功能描述:IC ADC 14BIT 105MSPS 40-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC2260CUJ-14-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:14-Bit, 125/105/80Msps Ultralow Power 1.8V ADCs |
| LTC2260CUJ-14-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:14-Bit, 125/105/80Msps Ultralow Power 1.8V ADCs |
| LTC2260IUJ-12#PBF | 功能描述:IC ADC 12-BIT 105MSPS 40-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。