- 您现在的位置：买卖IC网 > PDF目录10255 > LTC2351IUH-12#PBF (Linear Technology)IC ADC 12BIT 1.5MSPS 32-QFN PDF资料下载
参数资料
| 型号： | LTC2351IUH-12#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 5/20页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 1.5MSPS 32-QFN |
| 标准包装： | 73 |
| 位数： | 12 |
| 采样率（每秒）： | 1.5M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 16.5mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 管件 |
| 输入数目和类型： | 12 个单端，单极；12 个单端，双极；6 个差分，单极；6 个差分，双极 |
| 配用： | DC1278A-ND - BOARD SAR ADC LTC2351-14 |
LTC2351-12
13
235112fa
APPLICATIONS INFORMATION
SELECTING THE NUMBER OF CONVERTED CHANNELS
(SEL2, SEL1, SEL0)
These three control pins select the number of channels
being converted. 000 selects only the rst channel (CH0)
for conversion. Incrementing SELx selects additional
channels for conversion, up to 6 channels. 101, 110 or
111 select all 6 channels for conversion. These pins must
be kept in a xed state during conversion and during the
subsequent conversion to read data. When changing modes
between conversions, keep in mind that the output data
of a particular channel will remain unchanged until after
that channel is converted again. For example: convert
a sequence of 4 channels (CH0, CH1, CH2, CH3) with
SELx = 011, then, after these channels are converted
change SELx to 001 to convert just CH0 and CH1. See
Table 1. During the conversion of the rst set of two
channels you will be able to read the data from the same
two channels converted as part of the previous group
of 4 channels. Later, you could convert 4 or more chan-
nels to read back the unread CH2 and CH3 data that was
converted in the rst set of 4 channels. These pins are
often hardwired to enable the right number of channels
for a particular application. Choosing to convert fewer
channels per conversion results in faster throughput of
those channels. For example, 6 channels can be converted
at 250ksps/ch, while 3 channels can be converted at
500ksps/ch.
BIPOLAR/UNIPOLAR MODE
The input voltage range for each of the CHx input differ-
ential pairs is UNIPOLAR 0V – 2.5V when BIP is LOW, and
BIPOLAR ±1.25V when BIP is HIGH. This pin must be kept
in xed state during conversion and during subsequent
conversion to read data. When changing BIP between con-
versions the full acquisition time must be allowed before
starting the next conversion. After changing modes from
BIPOLAR to UNIPOLAR, or from UNIPOLAR to BIPOLAR,
you can still read the rst set of channels in the new mode,
by inverting the MSB to read these channels in the mode
that they were converted in.
DRIVING THE ANALOG INPUT
The differential analog inputs of the LTC2351-12 may be
driven differentially or as a single-ended input (i.e., the
CH0– input is grounded). All twelve analog inputs of all
six differential analog input pairs, CH0+ and CH0–, CH1+
and CH1–, CH2+ and CH2–, CH3+ and CH3–, CH4+ and
CH4– and CH5+ and CH5–, are sampled at the same in-
stant. Any unwanted signal that is common to both inputs
of each input pair will be reduced by the common mode
rejection of the sample-and-hold circuit. The inputs draw
only one small current spike while charging the sample-
and-hold capacitors at the end of conversion. During
conversion, the analog inputs draw only a small leakage
Table 1. Conversion Sequence Control
(“acquire” represents simultaneous sampling of all channels; CHx represents conversion of channels)
SEL2
SEL1
SEL0
CHANNEL ACQUISITION AND CONVERSION SEQUENCE
0
acquire, CH0, acquire, CH0...
0
1
acquire, CH0, CH1, acquire, CH0, CH1...
0
1
0
acquire, CH0, CH1, CH2, acquire, CH0, CH1, CH2...
0
1
acquire, CH0, CH1, CH2, CH3, acquire, CH0, CH1, CH2, CH3...
1
0
acquire, CH0, CH1, CH2, CH3, CH4, acquire, CH0,CH1,CH2, CH3, CH4...
1
0
1
acquire, CH0, CH1, CH2, CH3, CH4, CH5, acquire, CH0, CH1, CH2, CH3, CH4, CH5...
1
0
acquire, CH0, CH1, CH2, CH3, CH4, CH5, acquire, CH0, CH1, CH2, CH3, CH4, CH5...
1
acquire, CH0, CH1, CH2, CH3, CH4, CH5, acquire, CH0, CH1, CH2, CH3, CH4, CH5...
相关PDF资料 |
PDF描述 |
|---|---|
| VI-230-IW-S | CONVERTER MOD DC/DC 5V 100W |
| VE-22P-MX-F3 | CONVERTER MOD DC/DC 13.8V 75W |
| VI-230-CU-F4 | CONVERTER MOD DC/DC 5V 200W |
| VE-22P-MX-F2 | CONVERTER MOD DC/DC 13.8V 75W |
| VI-230-CU-F3 | CONVERTER MOD DC/DC 5V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2351IUH-14#PBF | 功能描述:IC ADC 14BIT 1.5MSPS 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2351IUH-14#TRPBF | 功能描述:IC ADC 14BIT 1.5MSPS 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC2351IUH-14PBF | 制造商:Linear Technology 功能描述:ADC 1.5Msps 14-Bit Serial QFN32EP |
| LTC2355CMSE-12#PBF | 功能描述:IC ADC 12BIT 3.5MSPS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2355CMSE-12#TRPBF | 功能描述:IC ADC 12BIT 3.5MSPS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。