- 您现在的位置：买卖IC网 > PDF目录10676 > LTC2355CMSE-12#PBF (Linear Technology)IC ADC 12BIT 3.5MSPS 10-MSOP PDF资料下载
参数资料
| 型号： | LTC2355CMSE-12#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/18页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 3.5MSPS 10-MSOP |
| 标准包装： | 50 |
| 位数： | 12 |
| 采样率（每秒）： | 3.5M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 18mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 10-MSOP 裸露焊盘 |
| 包装： | 管件 |
| 输入数目和类型： | 2 个单端，单极；1 个差分，单极 |
| 产品目录页面： | 1349 (CN2011-ZH PDF) |
| 配用： | DC1082A-F-ND - BOARD SAR ADC LTC2355-14 |
LTC2355-12/LTC2355-14
2355fa
applications inFormation
INPUT FILTERING AND SOURCE IMPEDANCE
The noise and the distortion of the input amplifier and
other circuitry must be considered since they will add to
the LTC2355-12/LTC2355-14 noise and distortion. The
small-signal bandwidth of the sample-and-hold circuit is
50MHz. Any noise or distortion products that are pres-
ent at the analog inputs will be summed over this entire
bandwidth. Noisy input circuitry should be filtered prior
to the analog inputs to minimize noise. A simple 1-pole
RC filter is sufficient for many applications. For example,
Figure 1 shows a 47pF capacitor from AIN+togroundanda
51Ωsourceresistortolimittheinputbandwidthto47MHz.
The 47pF capacitor also acts as a charge reservoir for the
input sample-and-hold and isolates the ADC input from
sampling-glitchsensitivecircuitry.Highqualitycapacitors
and resistors should be used since these components
can add distortion. NPO and silvermica type dielectric
capacitors have excellent linearity. Carbon surface mount
resistors can generate distortion from self heating and
from damage that may occur during soldering. Metal film
surface mount resistors are much less susceptible to both
problems.Whenhighamplitudeunwantedsignalsareclose
in frequency to the desired signal frequency, a multiple
pole filter is required. High external source resistance,
combined with the 13pF of input capacitance, will reduce
the rated 50MHz bandwidth and increase acquisition time
beyond 39ns.
INPUT RANGE
The analog inputs of the LTC2355-12/LTC2355-14 may be
driven fully differentially with a single supply. Each input
may swing up to 2.5VP-P individually. When using the
internal reference, the noninverting input should never be
more than 2.5V more positive than the inverting input. The
0V to 2.5V range is also ideally suited for single-ended
input use with single supply applications. The common
mode range of the inputs extend from ground to the sup-
ply voltage VDD. If the difference between the AIN+ and
AIN– inputs exceeds 2.5V, the output code will stay fixed
at all ones and if this difference goes below 0V, the ouput
code will stay fixed at all zeros.
INTERNAL REFERENCE
TheLTC2355-12/LTC2355-14hasanon-chip,temperature
compensated, bandgap reference that is factory trimmed
to 2.5V to obtain a unipolar 0V to 2.5V input span. The
reference amplifier output VREF, (Pin 3) must be bypassed
with a capacitor to ground. The reference amplifier is
stable with capacitors of 1F or greater. For the best noise
performance,a10Fceramicora10Ftantaluminparallel
with a 0.1F ceramic is recommended. The VREFpincanbe
overdriven with an external reference as shown in Figure
2. The voltage of the external reference must be higher
than the 2.5V output of the internal reference. The recom-
mended range for an external reference is 2.55V to VDD.
An external reference at 2.55V will see a DC quiescent load
of 0.75mA and as much as 3mA during conversion.
Figure 1. RC Input Filter
Figure 2. Overdriving VREF Pin with an External Reference
10F
11
3
AIN–
LTC2355-12/
LTC2355-14
AIN+
47pF
2
1
51
GND
VREF
2355 F01
GND
LTC2355-12/
LTC2355-14
LT1790-3
VREF
10F
3.5V TO 18V
11
3
3V
2355 F02
相关PDF资料 |
PDF描述 |
|---|---|
| VI-25N-IX-B1 | CONVERTER MOD DC/DC 18.5V 75W |
| AD7895ARZ-10 | IC ADC 12BIT SRL 5V 8-SOIC |
| VI-B61-MY-B1 | CONVERTER MOD DC/DC 12V 50W |
| VI-JWB-MY-F4 | CONVERTER MOD DC/DC 95V 50W |
| VI-204-IX-B1 | CONVERTER MOD DC/DC 48V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2355CMSE-14#PBF | 功能描述:IC ADC 14BIT 3.5MSPS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2355CMSE-14#PBF | 制造商:Linear Technology 功能描述:IC, ADC, 14BIT, 3.5MSPS, MSOP-10 |
| LTC2355CMSE-14#TRPBF | 功能描述:IC ADC 14BIT 3.5MSPS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC2355IMSE-12#PBF | 功能描述:IC ADC 12BIT 3.5MSPS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2355IMSE-12#TRPBF | 功能描述:IC ADC 12BIT 3.5MSPS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。